You are viewing all articles in Programming -> Programming Mobile Decoders -> Programming Modes (including subcategories). To further filter by subcategory, select from below.
Zephyr Xtra (DCS51) and Zephyr (DCS50) systems can program Soundtraxx Tsunami decoders using Blast Mode Programming on the Mainline. Blast Mode Programming will program EVERYTHING sitting on the main line track so, you MUST remove everything from the track that you are not programming or use an isolated piece of track connected to Rail A & B. NOTE: Track power must be ON during Blast Mode Programming. Blast Mode programming will work with all sound decoders not just Tsunami. You will not be able to read back CVs using Blast Mode Programming. To use Blast Mode Programming with Zephyr, close ...
This procedure should be done on an electrically isolated programming track1. Be sure that only the locomotive you want to program is on the programming track.2. Press the PROG key on the DCS50 to enter programming mode. The DCS50 will display one of the programming modes available. Digitrax recommends the Paged Mode when you are using the programming track. If you press the PROG key repeatedly, you will cycle through the following choices: PAGE PHYS dir OPSFor example, to use Paged mode stop pressing the PROG key when the following screen appears:Each time you press the LOCO key the ...
To use the UT2 to program a decoder you must first put the UT2 in Programming Mode. To do this press and hold “RUN/STOP” and simultaneously press “PROG”. The Status LED will now turn a steady orange color indicating the UT2 is now in Programming Mode. Set the locomotive you wish to program on an isolated programming track (See Section 5.2). Make sure that the DB150 command station is not connected to any other part of the layout. If you don’t have a programming track on your layout remove any locomotive you don’t want programmed at this time. Decoders ...
Ops Mode programming, also known as "Programming on the Main" lets you change the configuration of an individual decoder while the locomotive is on your railroad without having to move it to the programming track.Operations mode programming lets you program CVs in DCC locomotives equipped with Ops mode capable decoders while they are on the mainline. A typical use for Ops mode programming would be to change the acceleration rate (CV03) or the deceleration rate (CV04) of your locomotives to simulate the weight and braking capability of the train to compensate for changing the number of cars or power units on a ...
Programming On The Mainline: Operations Mode ProgrammingOperations Mode Programming [Ops Mode] lets you program CVs in DCC locomotives equipped with Extended Packet Format decoders while they are on the mainline. This is handy for situations where you want to make an adjustment to a specific locomotive while it is in service. There are also situations where mobile decoders from other manufacturers can only be programmed in this manner. A typical use for Ops mode programming would be to change the acceleration rate (CV03) or the deceleration rate (CV04) of your locomotives to simulate the weight and braking capability of the ...
This article was originally posted on this site in 2006, but the source material dates back much further than that, probably back to the early 1990's, when DCC was an emerging control system. The article discusses non-sound mobile decoder programming operations. Many of the issues discussed in this article are less relevant when using recently produced decoders, but this text still does cover some questions which may be raised when you are using mobile decoders which were manufactured by other companies. These decoders will operate in the Digitrax environment, but you may need to make some adjustments.The earliest Digitrax mobile ...
In addition to the locomotive address, there are different Configuration Variables (CV's) that have been defined to handle many characteristics you might want to use for your locomotives. These include operational characteristics such as acceleration, headlight functions and others. The manual for each decoder type has a complete listing of CVs that are available in specific decoders, what they do and the suggested values for each CV. Simpler decoders have few CVs while advanced decoders may have many different CVs 1. Place the decoder equipped locomotive you want to program on the programming track If you are using operations mode ...
If you have trouble reading back CV's on the programming track, this may be due to insufficient current draw on the SFX064D function leads. You can always just re-program the CV value into a CV to get the desired results, even though reading CVs does not work. OPs mode is recommended for programming all CVs except CV01, CV17 & CV18 (2 digit and 4 digit addresses). If a second DCC decoder is present that is not Sound FX compatible then correct readback of CV data is not possible, since the NMRA CV readback was not designed for multiple decoder readback.
Duplex Radio Throttle do not need to be plugged in to LocoNet to Program Decoders. Simplex Radio & Infrared throttles must be plugged in to LocoNet to program CVs on the programming track. Ops Mode Programming can be done without plugging radio throttles in to LocoNet. IR throttles must be plugged in for Ops Mode Programming. 1. Be sure that only the loco you want to program is on the programming track. If you are using operations mode programming, the loco you want to program can be anywhere on the layout but it must have a decoder that is ...
There are many different CVs that have been defined to control operating characteristics of your locomotives. Your decoder manual has a complete listing of CVs that are available with specific decoders, what they do and suggested values for each CV. Programming these CVs is simple:1. Be sure that only the locomotive you want to program is on the programming track.2. Press the PROG Key to enter programming mode. The DCS50 will display one of the programming modes available. Digitrax recommends the Paged Mode when you are using the programming track. As you press the PROG Key repeatedly, you will cycle ...
Q: How can I write and read the Configuration Variables of Mobile Decoder on the mainline using the DT40x Throttle? A: Operations Mode Programming, also known as Ops Mode, lets you program a locomotive decoder's CVs while it is on the main line. With the addition of transponding in Ops Mode, you can write and read back CVs in DCC locomotives equipped with most modern decoders while they are on the mainline. Some older decoders before Extended Packet Format was used are not able to do this.For example: A typical use for Ops mode programming would be to adjust an engines ...
Operations mode (OPs mode) programming allows you to program decoders on the layout instead of having to move them to a separate programming track. This is a write only programming method. If you want to be able to read back the values written to a particular decoder using Ops Mode programming, you will need to install transponding on the layout. If transponding is not active on the layout, you must use an isolated programming track for reading back CV values.The extent of the area with OPs Mode readback available depends on how muchof the layout is instrumented for transponding. The ...