Programming is the process of setting the configuration variables (CVs) in your decoder to the appropriate values that will make the locomotive perform the way you want it to. The first CVs that most people change are those that set the locomotive decoder's address. The mobile decoder in your locomotive usually comes pre-porgrammed to a factory default address of "03". Once you add a second locomotive, you will want to change the this new locomotive to another address. Not doing so will result in both locomotives operating at the same time when you send commands to address 03.Likewise, there are a ...
This procedure should be done on an electrically isolated programming track1. Be sure that only the locomotive you want to program is on the programming track.2. Press the PROG key on the DCS50 to enter programming mode. The DCS50 will display one of the programming modes available. Digitrax recommends the Paged Mode when you are using the programming track. If you press the PROG key repeatedly, you will cycle through the following choices: PAGE PHYS dir OPSFor example, to use Paged mode stop pressing the PROG key when the following screen appears:Each time you press the LOCO key the ...
What is the difference between programing on the layout using Track A and B and using a dedicated programing track using Pgm A & B. Is there a difference in voltage, packets, protocol between the two? Programming Track Broadcast programming, also called service mode programming, uses a programming track. The programming track is electrically separate from the rest of the railroad, and is connected to the "PROG A" and "PROG B" terminals of your DCS100/200 or Zephyr (Xtra) command station.One major advantage to a programming track is that many systems can read-back the Configuration Variables (CV's) that are in ...
The DT402 & DT400 can program and readback CVs with the DCS100 or DCS200 (Super Chief) or the DCS51 or DCS50 (Zephyr). You must use the programming track for this unless you are using Ops Mode with transponding installed to allow for Ops Mode readback. Infrared and simplex radio throttles must be plugged in to LocoNet to read back CVs & their values. Duplex radio throttles do not have to be plugged in for reading back CVs.Systems with a DB150 command station (Super Empire Builder) are not able to read back CV Values programmed into decoders. To read back CV values: 1. Place the decoder ...
Your DCS50 can read back the CV data values programmed into your decoders. You will use your programming track for reading back CV data values.To read back CV values using a programming track:1. Be sure that only the locomotive you want to read back is on the programming track.2. Press the PROG key to enter programming mode. The Zephyr DCS50 will display one of the programming modes available. Once the mode you want to use is on the screen you can go to step 3.For example, to use Paged mode stop pressing the PROG Key when the following screen appears:3. ...
If you have trouble reading back CV's on the programming track, this may be due to insufficient current draw on the SFX064D function leads. You can always just re-program the CV value into a CV to get the desired results, even though reading CVs does not work. OPs mode is recommended for programming all CVs except CV01, CV17 & CV18 (2 digit and 4 digit addresses). If a second DCC decoder is present that is not Sound FX compatible then correct readback of CV data is not possible, since the NMRA CV readback was not designed for multiple decoder readback.
Q: How can I write and read the Configuration Variables of Mobile Decoder on the mainline using the DT40x Throttle? A: Operations Mode Programming, also known as Ops Mode, lets you program a locomotive decoder's CVs while it is on the main line. With the addition of transponding in Ops Mode, you can write and read back CVs in DCC locomotives equipped with most modern decoders while they are on the mainline. Some older decoders before Extended Packet Format was used are not able to do this.For example: A typical use for Ops mode programming would be to adjust an engines ...
Operations mode (OPs mode) programming allows you to program decoders on the layout instead of having to move them to a separate programming track. This is a write only programming method. If you want to be able to read back the values written to a particular decoder using Ops Mode programming, you will need to install transponding on the layout. If transponding is not active on the layout, you must use an isolated programming track for reading back CV values.The extent of the area with OPs Mode readback available depends on how muchof the layout is instrumented for transponding. The ...