Product Support for: Command Stations & Boosters -> 8 Amp DCC Opto Booster (DB200 OPTO)

Single 3/5/8 Amp AutoReversing DCC Booster with up to 8 Amps of power total. Opto-Isolated for layouts with common rail wiring

DB200 Plus 8 Amp Booster gives you 8 amps of power to run more trains, manage short circuit shutdowns and add automatic reversing. Great for adding more power to layouts running many locos or large-scale locos. Beef up your layout!

The actual track voltage supplied by the DB200 can be adjusted. To adjust the track voltage, you must open the DB200 case (this will not void your warranty). 1. Remove the DB200 input power & disconnect all DB200 leads. 2. Remove the two screws on the top and bottom of each side of the case. 3. Slide the gray front panel off the DB200. 4. Be careful to avoid disturbing components other than the ones described below. 5. Locate the small yellow trimmer potentiometer behind the LocoNet B Jack and Scale Switch. 6. Use a small screwdriver to turn the ...

You can have the power and reliability of Digitrax boosters even if you use a Lenz Command Station. You can use Digitrax boosters to automate reverse loops, too. Digitrax boosters can be used with the Lenz Command Station to provide more power for driving the layout. Many customers are using DB150, DB200, or DB100 series boosters instead of LV100's because the DB150’s & DB100's are very reliable 5 amp boosters with plenty of heat sinking capability to prevent heat related booster shutdows. Equipment needed: 1) A Lenz LZ100 Command Station. 2) A DB150, DB100 or a DB200 series booster. 3) ...

  This document outlines the power requirements for Digitrax LocoNet accessories.  To simplify wiring, Digitrax recommends providing individual power supplies for like accessories.  For example a power supply or power buss which only powers the PM42s.  A power supply or power buss used solely to power multiple DS64s.  UR9x and UP5 panels can be daisy chained provided adequate current is provided to properly power all the panels.  Through the use of individual power supplies, the chance of Ground Loops or sneak paths back to ground is minimized.  Using individual power supplies will also make troubleshooting much easier.  Many Digitrax LocoNet ...

We have a number of customers who are running Digitrax alongside their existing block detection circuitry. There are numerous block detection schemes and circuits, and we cannot cover all the variations here. Generally, it is necessary to isolate the block detector power supply and ground system of your existing block detector system from that of the Digital boosters. The most common detectors use "back to back" high current diodes to sense block current-draw. Detectors with "opto-isolated" or relay outputs will generally have no problem sensing current draw of a loco, etc., on the DCC current, and will signal the occupancy ...

 OpSw Setup Enter OpSw mode by pressing the OpSw button.  The OPS and ID light will flash alternating RED and GREEN. Use your throttle in SWITCH mode to set switches to thrown or closed to match your desired OpSw setting.  There are currently no published OpSws for the BXPA1. If you erroneously set an OpSw, the BXPA1 can be factory reset by setting OpSw40 = Closed Trip Speed Pot The Trip Speed Pot can be adjusted to set the speed at which auto reversing and power management is resolved.  Turning the pot clockwise will make the speed slower and turning ...

The DB200+ is the 8 amp booster. It has NO command station capability. This booster was designed for adding power to layouts that run lots of locos and for large-scale layouts where power requirements are heavy.DB200+ Control PanelNOTE: DB200+ front panel graphics may vary from those shown here.  Internally the booster is the same. These instructions are written for both versions of graphics as well as the DB200+ OPTO optoisolated version of the booster. About the Green Jumper WireEvery DB200+ is shipped with a green jumper wire on the front panel Booster Terminal Plug connecting Synch & Ground or ‘Config ...

The PS615 is the Digitrax recommended power supply for the DCS240 in 5 amp mode.  For operations at 8 amps the PS2012 is the recommended power supply. When using the PS2012 special wiring considerations need to be used when powering both the DCS240 and legacy boosters from the same PS2012.  Leagacy boosters are defined as the DCS100, DCS200, DB150, DB200 or DB100.  Please see the separate article “Powering your DCS240 with a PS2012” and the additional notes below. The DCS240 may be powered either using the barrel plug connector or the screw terminals labeled “+” and “- “. The barrel ...

Digitrax Complete Train Control By Zana & A.J. Ireland Digitrax Complete Train Control makes reliable, realistic train operation and simplified layout wiring a reality. Digital Command Control is incorporated within the Digitrax system to let you control multiple trains independently on the same section of track without blocking. In the real world, engineers control the speed and direction of real trains. Engines operate under their own power independent of the track. Each engine has its own motion characteristics like how fast it speeds up (acceleration) and how long it takes to slow down (deceleration). A locomotive's performance is influenced by ...