I am installing a DH165A0 in an Athearn SD70. The head light outputs are a nominal 30 ma (with the link cut). The bulbs were of course a bit lower in their current demands and were very bright for a short while. Is there any way to lower the current output from 30ma or do I need to add a resistor in line with the bulb to drop the voltage output? Of course if it is supposed to be a regulated current output this might be a problem. The DH165A0 has a constant current source for F0F and F0R, so ...
Q: My front and rear lights on a steam locomotive (hard wired decoder installation) are connected in reverse. When the locomotive is going forward, the back up light comes on. When the locomotive is going in reverse, the forward light comes on. Can I reverse the lighting effects though programming the decoder or must I disassemble the locomoitve and physically swap the wiring to the lights from the decoder. A: Yes, you can do this with using function mapping in any Digitrax decoder Series 3 or later. If you have an earlier version decoder installed, you'll need to re-wire the ...
Configurable strobes are set up using CV's 49, 50 and 61. Configurable strobe function leads can be programmed with a limited number of simulated lighting effects similar to FX effects but without as many options. Configurable strobes are offered in those few Digitrax decoders where there was not enough "code space" to provide full FX features.CV49 controls F0 Forward, the white function lead. CV50 controls F0 reverse, the yellow function lead.CV61 enables the configurable strobe operation.To set up configurable strobe lights:1. Program CV61 with the CV value "01" to enable configurable strobe operation.2. Program the CV value for CVs 49 ...
The headlights of my locomotive aren't acting properly. If you can’t control the operation of the lights in your locomotive with the DT400 (in default 128, or 28 speed step mode), be sure that the decoder is programmed in advanced 28 speed step mode. Do this by programming CV29 with a decimal value of 06.
Rule 17 refers to how a locomotive engineer operates the locomotive's headlights while running the train. Rule 17 is part of a railroad's standardized rulebook. Rule 17 varies from railroad to railroad. Typically, it requires dimming the headlight when the locomotive is standing in a siding waiting to meet another train, passing through passenger stations or moving within yard limits. Program CV49 to 104 to set Function 0 to implement Rule 17 dimming.
The DT400 can control Functions 1 - 12.Note: DT400 can access F0-F12 when used with the DCS50 Zephyr or DCS100 Super Chief command station. DT400 can only access F0-F8 when used with a DB150 Super Empire Builder command station.To enter Fn (function) mode:1. Determine which throttle you want to control functions on and make it the active throttle by single clicking the throttle knob or by turning the throttle knob a couple of clicks.2. DT400’s numeric keypad is always active in function mode during normal loco operations. When the mode indicator on your DT400 shows Fn, simply press any number ...
The DZ125 is set up at the factory to control two function outputs. The DZ125 is configured to control the forward and reverse lights on the locomotive through the white lead and yellow lead using Function 0 (F0F-forward and F0R-reverse) for directional lighting. Both function outputs can be easily set up with Digitrax FX3 lighting effects or as standard on/off functions with the following operational qualifiers: 1. Forward or Reverse direction of travel, or 2. Whether F0 is on or off, or 3. Both direction of travel and whether F0 is on or off, or 4. Whether the locomotive is ...
I'm trying to install a DH123D decoder in a Life like P2K PA loco and make the mars light work. HELP! Because the DH123D is a two-function decoder (front headlight, rear headlight), it may not be the best decoder choice for this locomotive. In practice, some PA's had only one headlight, thus there would be no Mars light. The DH123D would be an appropriate choice for those locomotives. Typically, eastern railroads would just have one headlight; think Pennsy and Southern Railway. Western railroads, because of higher train speeds, often used warning lights such as the Mars Light or Pyle Gyra-Light; ...
Configurable strobes are controlled with CV49 & CV50. CV49 controls the White Lead CV50 controls the Yellow Lead The value programmed for each CV consists of 2 digits, the first digit controls the conditions under which the light will be active.1x=Reverse, if 1 is the first digit then the light will be on when the locomotive is in reverse2x=F0 Qualified, if 2 is the first digit then the function will be active when F0 is on and off when F0 is off4x=Direction insensitive, if 4 is the first digit then the function will be On in either directionThe second ...
There is a numeric keypad on the DT402/DT400 throttle. The numeric keys on the keypad are primarily related to the throttle mode shown in the LCD’s mode indicator area, but can be used for numeric entry and function control in other modes. For example, when the command station is in the Function Mode Fn, the numeric keys are used for function control. When the command station is in the Locomotive Mode,Lo, the numeric keys are used to enter loco addresses. When the command station is in the Switch Mode is Sw, the numeric keys are used to enter switch addresses.In ...