FX & FX3 Functions-Special Lighting Effectcs

I have a Athearn HO Scale MP15 Soo Line and have installed a DH166 decoder. How do I get the rotary beacon to flash? Function Outputs on the DH166 The DH166 is set up at the factory to control six function outputs. The DH163AT is configured to control the forward and reverse lights on the locomotive through the yellow lead and white lead using Function 0 (F0F-forward yellow and F0R-reverse white) for directional lighting. Functions F1(green) and F2 (violet) are part of the harness for easy hookup. F3 and F4 are also available on the decoder board. These can be ...

Many locomotives feature warning lights that are designed to make a train more visible to the general public. FX Functions are function outputs that incorporate 4 FX generators for prototypical lighting effects such as Mars lights, ditch lights, Pyle Gyra-lights, rotating beacons, single and double pulse strobe lights, and random flicker.

All current Digitrax mobile decoders have FX3: all function outputs incorporate FX generators for prototypical lighting effects full function re-mapping so you can choose which function (F0-F12) controls each function lead

 Digitrax Series 3 Decoders include the following features and more: FX3 Function Outputs Supersonic motor drive for quiet operation Support for all DCC programming methods One-Step decoder factory CV reset Motor isolation protection White or Golden Yellow LEDs on decoders that come equipped with LEDs Operations mode read back capability for CV read back on the main line

There is a numeric keypad on the DT402/DT400 throttle.  The numeric keys on the keypad are primarily related to the throttle mode shown in the LCD’s mode indicator area, but can be used for numeric entry and function control in other modes. For example, when the command station is in the Function Mode Fn, the numeric keys are used for function control. When the command station is in the Locomotive Mode,Lo, the numeric keys are used to enter loco addresses. When the command station is in the Switch Mode is Sw, the numeric keys are used to enter switch addresses.In ...

Decoders with FX3 features have 8 user configurable, independent special effects generators.  All current production Digitrax Decoders use FX3 function features. These are set up by programming CV values as described below.  If your decoder is not a Series 3 decoder, please check the spec sheet to determine which type of functions it supports.FX3 functions incorporate FX generators with additional dynamic and static qualifiers.  FX3 functions are fully remappable so they can be controlled by any function key on your system.  A master light switch can be set up to turn off all lights on a locomotive. Functions associated with advanced ...

Decoders with FX function features have 4 user configurable, independent special effects generators. All current production Digitrax Decoders use FX3 functions so this article is not applicapable to these decoders. CAUTION: Decoders with FX3 function generators use different CVs to control the decoder outputs. All current production Digitrax decoders use FX3 function CVs. Before using these CVs to program your decoders make sure that they are FX and not FX3 decoders.The Real FX effects are set up by programming CV values as described below.F1/F2 NOTE: If using DH142, DN142, DN141K2, DN149K2 series decoder, when F1 is set up for FX, ...

Flashing ditch lights can be set up with several CV's. Using 1.5 Volt Bulbs or LEDsIf you use 1.5 V bulbs, you must install a current setting resistor with a minimum value of 100 ohms for each bulb.Typically a 560 ohm 1/4 watt resistor works well for a grain of rice bulb and a 250 ohm 1/4 watt resistor works well for a grain of wheat bulb.Lower resistance values will increase the lamp brightness. If you use LED's be sure the polarity is correct when you hook them up & install a current setting resistor for each LED. Typically a ...

The DT400 can control Functions 1 - 12.Note: DT400 can access F0-F12 when used with the DCS50 Zephyr or DCS100 Super Chief command station. DT400 can only access F0-F8 when used with a DB150 Super Empire Builder command station.To enter Fn (function) mode:1. Determine which throttle you want to control functions on and make it the active throttle by single clicking the throttle knob or by turning the throttle knob a couple of clicks.2. DT400’s numeric keypad is always active in function mode during normal loco operations. When the mode indicator on your DT400 shows Fn, simply press any number ...

Remove the 8 pin dummy plug from Lifelike Proto 2000 light board.Before installing the decoder in the locomotive, unsolder the yellow wire from pin 2 and re-solder it to pin 3 (empty pin) on the decoder harness plug board.  We strongly recommend that you mark the decoder and/or harness so that you will remember that you have modified it.  If you use the decoder and/or harness modified in this manner in a different locomotive, your lights will not work correctly. Plug the decoder and harness into the light board in the locomotive.Program CVs as follows:  CV33 = 001, CV34 = ...

FX3 decoders have motor isolation protection. If the decoder senses that the motor is not isolated, it will not run the motor. In this case, you will be able to control the loco’s functions but the motor will not work.FX decoders will blink the loco's lights when power is first applied to the decoder to warn you of a short circuit in your installation. If you see the lights blinking, immediately remove the loco from the track, locate the short circuit and correct the problem before proceeding. Do not leave the loco on the track with blinking lights because eventually, ...