Bachmann Locomotives

How to add DCC to the new run of Bachmann DCC ready Dash 8-40CW? The current recommendation is for direct soldering, using either DZ125, which controls headlights only or DZ143, which controls headlight and two additional functions. With earlier units, either milling of the frame or a replacement frame was necessary, but the new units have a "DCC ready frame"; the source of this information also points out that Bachmann is using the same model number for both the older version and the newer version, so you should make certain that you have the recent version.

Q:  I have a Digitrax Chief system. I wired the programming track as per the manual, using PROGA and PROGB outputs on the DCS100. I turned on the system and checked the track voltage with a Tony Trains RRamp meter, the mainline read 14.2 volts. The programing track did not read anything. I then checked the two wires coming from the DCS100 and they did not have any readable signal. A:  The programing track connected to PROG A and PROG B will NEVER have track power on except the very instant the program message is sent.  So, you would not ...

This article courtesy of Ross Webster, which dates from an earlier era before Bachmann made accommodations for DCC installs:There may be others ways do to this conversion, but this is the way I found using the Digitrax DG380 (any DG wired decoder can be used for this installation) DUE TO SOME OF THE FRAGILE ITEMS ON THE SHAY I WORKED ON A FOAM PAD SO THERE WAS NO DAMAGE TO ANY OF THE SMALL PARTS.I first tested the electrical items and made the following determinations.Free running for the two trucks was .8 amps, total. Stall, was 4.6 amps total for both trucks. Smoke ...

This note addresses the installation of an H0-Scale wired decoder into Bachmann Plus ABA F-7s; it calls for using a DH140, which has been retired.  Current decoders such as the DH123 or DH163 or similar wired decoders can be used. Just finished up doing a few HO Bachmann Plus F7's, ABA's to be exact. Thought maybe some of you might be interested in how the DCC conversion went on these.They are an easy conversion!1.  The full stall current for these ranged from 500-700 ma for each loco . I selected Digitrax DH140 for the A units and a DH120 for the B ...

This application note is courtesy of Michael K. Perrin, and addresses the installation of an N-Scale decoder in the Bachmann F40PH (now discontinued).  This note calls for using either DN93 or DN140, both of which have been discontinued.  Current decoders such as the DZ125 or DZ143 and other similar N scale decoders can be used.1) Cut a place for the decoder in the back recess in the frame. Because this is a "sandwich" frame there is no room for the decoder without using a saw or Dremel tool to make a cavity for the decoder. (This is the hardest part of the ...

Q:  I have seen notes several times where the author recommends removing the capacitors that are in the Bachmann circuit boards before installing a DCC decoder. Can you comment on the need for this? Is it universal for the Bachmann steam locos? A:  As a rule, all capacitors must be removed from locos before installing decoders. Also, any choke coils must be removed, too. Both capacitors and choke coils cause problems with DCC signals. If you are unsure, a Google search for the locomotive type and the term "DCC" often produces an article specifically about the locomotive installation in question.

Many thanks to Dick Sutcliffe, Superintendent BR &T Railway Co. for this application note!Install the DN121 in the tender   1. The tender is easy to open by removing two screws so you can pull the decoder out and put in a plug when running on DC layouts.   2. Use a piece of styrene to raise the decoder off the weight.   3. Notch the front edge of the tender frame to bring the wires through to loco (all power pick up is in the loco).   4. Split the loco frame to isolate the motor brushes, remove the contact springs in the ...