Super Empire Builder Starter Set

The track power indicator on your DT400 shows whether track power is on or off. If the track power indicator is lit then track power is on. There is also a Track Power indicator on your command station.To Turn Track Power On:If the Track Power Indicator is not lit, turn track power on as follows:1.  Press the PWR Key2.  Press the Y + Key and the Track Power Indicator on your DT400 display and on your command station will come on solid. If the Track Power Indicator is blinking, press the Y+ Key again to make it solid and turn ...

If you want to change the address or other settings of your locomotive decoders, you must set up a programming track. It is very important that the rest of your railroad can be isolated from the DB150 and the programming track when you are programming a locomotive. Decoders are programmed when the DB150 command station sends programming information to them through the rails. There are two basic ways of programming decoders. Service mode programming broadcasts a message to all DCC equipped locos that are on the track. Because this is a broadcast method, you will need to set up a ...

Shutting Down the System When you are finished with your sessionDispatching All Locomotive Addresses Some users prefer to “dispatch” or release all addresses active in their system before shutting down. This can prevent unexpected results when you power up the layout again. 1. Turn track power off: Press the PWR Key followed by the N - Key , the Track Power Indicator on the DT400 and the Track Status Indicator on your command station will go off. 2. Move the DB150 command station’s “MODE” switch to the “SLEEP” position. 3. Turn off the power supply to the system. Leaving the ...

How To Turn Track Power On and Off with the DT400 series throttle Turn track power on: Press the PWR Key, then press the Y + Key and the Track Power Indicator on your DT400 series display and on your command station will come on solid. If the track power indicator is blinking, press the Y+ key again to make it solid. Turn track power off: Press the PWR Key , then press the N - Key . The Track Power Indicator on your DT400 series and on your command station will go off. To Exit: Exit PWR mode by pressing the ...

The DT400 series’ Track Power Indicator and the DB150’s track status indicator show whether track power is on or off. The first time you plug in your DT400 series throttle, track power will usually be off. To run trains, you will need to turn on the track power. Look at your DB150 and/or DT400 series to determine whether the track power is on or off. 1. When track power is off: DB150 TRACK STATUS indicator is off DB150 OFF LINE indicator is on and DT400 series Track Power Indicator is off (Track Power Indicator is a small dot in the top line on ...

The actual track voltage supplied by the DB150 can be adjusted. To do this, you must open the DB150 case (this will not void your warranty). 1. Open the DB150 case. Remove the black screws on the top and bottom of the case and slide the gray front panel off. Be careful to avoid disturbing components other than the ones described below. 2. Locate the small yellow trimmer potentiometer behind the LocoNet B Jack and Scale Switch. 3. Use a small screwdriver to turn the potentiometer clockwise to increase the scale voltage setting. Turn it counter clockwise to decrease the ...

Q:  I have three engines lashed together. The sound is coming through . However when I turn the knob there is no response. The engine in the window is blinking and there are two stationary dots above A:  If you are using a DT300 series or DT400 series throttle, make sure that the Track Status Indicator dot in the upper right of the display just below the right throttle knob is on solid.  If it is not on at all Track Power is OFF.  If it is blinking, Track Status is in Idle and the throttle knobls will not move the locos.  To ...

The front panel of the DB150 Super Empire Builder has electrical connection points, indicator lamps, LocoNet connections and toggle switches which give status indications, configure and connect the unit for your railroad. Power Input The two “POWER IN” terminals on all Digitrax boosters & command stations are the power input connections. Please see the related articles about power requirements for the DB150. Power Supply Digitrax recommends the PS515 power supply to power the DB150. There are many other transformers and power packs that can supply the input power for the DB150. Check with your Digitrax dealer for suggestions. Most regular ...

These instructions will get you up and running quickly. A full description of all controls and technical reference information are included later in this section of the Tech Support Depot. This section assumes that you are using a new set straight out of the box. If your set is radio equipped, we recommend that you follow this quick start guide without using radio to learn the basics. When you are successfully running your radio throttle tethered to the system, then go to the DT400 series tetherless overview article to learn how to install the radio option. Connect the DB150 to the ...

Your Super Empire Builder Starter Set contains: The DB150, which is the system’s DCC command station. It generates the DCC signals that control decoders and other devices on your layout. The DB150 is also a DCC booster. Boosters receive DCC signals from the command station, amplify them and put them on the track along with the power from the transformer to run the locomotives. You can have several boosters on your layout to provide additional power to run more locos. Depending upon the set, there is either a DT402 or DT402D (duplex radio throttle), which is the DCC throttle that ...

If the DB150 beeps 5 times and shuts down briefly and then comes back on again. It is probably being run too close to its pre-set current limit. To solve this problem, reduce the track current load by setting up additional power districts to provide more total power for the layout. In this case excess current consumption may clip or mutilate some outgoing packets to keep the track current within acceptable limits.

The DT402 & DT402's screens are an LCD (Liquid Crystal Display) that is designed to show you what you are controlling with the throttle.  It also facilitates programming and other features of the LocoNet system. 1. The handheld has two throttles called the left throttle (L) and the right throttle (R).2. There are two direction indicators. One for the L throttle and one for the R Throttle. If the direction indicator is lit, and there is smoke over the loco icon there is an address selected on that throttle.3. The direction indicator with blinking smoke indicates which throttle is currently active. The ...

Super Empire Builder superseded Empire Builder II Super Empire Builder Included A DT400 throttleA DB150 Command Station/BoosterA UP5 Universal PanelA Short LocoNet CableInstruction Manuals

There are times when it is necessary to reset the Super Empire Builder. Because this is a system reset, there are special instructions: There are different levels of system reset. OpSw 36: Clears all mobile decoder information, including locomotive consists. OpSw 38: Clears the locomotive roster (such as when you receive a "slot=max" error report). OpSw 39: Full reset, clears all internal memory states. The factory default setting for all DB150 option switches is t or "thrown" The Initial Procedure 1. Determine which DB150 option switch you want to change, 36, 38 or 39. 2. Move the Mode toggle switch on ...

'It is possible to operate one conventional DC locomotive at Address 00.  In many cases, this is the first locomotive that beginners use when they first get their command control system.  In other cases, this locomotive is one which cannot be easily converted to DCC.  Regardless, although it is possible to use your Digitrax system in this way, it is not a recommended approach.1. Place an analog locomotive (one without a decoder) on your layout.  While the analog loco is sitting still, you will hear the characteristic “singing” caused by the DCC track signal when it is applied to analog ...

Digitgrax refers to the throttle knob on the left side as the L Throttle and the throttle knob on the right side as the R Throttle. This corresponds to the L & R that appears on the throttle. The throttle knobs on the DT400 use “encoders.” They give very smooth, fine speed control. In 128 speed step mode it takes four complete rotations of the knob to go from stop to full speed. When you select a locomotive that is already moving on either throttle knob, that throttle will continue to run the locomotive at the same speed and in the ...

I own a Digitrax Starter Set that is now discontinued. Can I still use it and can it be upgraded?LocoNet lets you use all Digitrax LocoNet components in your system no matter when you purchased them. You can continue to use what you already own with new components as they become available. Note:  This will work with all starter sets except for Challenger. If you have a Challenger Set and you want to move up, the best thing to do is to purchase one of the new sets and use the DB100 series booster that came with your Challenger as ...

1. Plug the DT402 & DT400 series throttle into any functioning Digitrax LocoNet System or other LocoNet compatible system and you are ready to go! You can use any LocoNet jack on your system.2. First, you will see the DT402 or DT400 version number screen: This screen shows the throttle's software version number. It is displayed for a few seconds each time you power on the throttle.3. Next you will see the power indicator screen: This screen indicates the power available to the throttle. When you are plugged in to LocoNet, this value will be between 9 & 15 volts. When you ...

The answer to this question applies to all Empire Builder sets including Super Empire Builder XtraQ:  I have just purchased a Super Empire Builder set. My expectations are for it to operate an N-Scale switching layout right now with future expansion to a larger N-Scale layout. I am a little confused as to which power supply I would need at this time. I am reading about power supplies and inline fuses, all of which is a little overwhelming to me as I am getting back into the hobby. Can you recommend which power supply will be better for me as ...

  Option switches are used to change the operation of the DB150. Option Switch # Effect on system when Option Switch “c” closed Default OpSw 02 Booster Only override t OpSw 03 DB150’s booster is auto reversing t OpSw 05 Default closed for command station –DO NOT CHANGE- c OpSw 13 Loco purge time extended from 200 seconds to 600 seconds t OpSw 14 Loco purging is disabled t OpSw 15 Purging will force loco to Stop or 0 speed t OpSw 17 Automatic advanced decoder assisted [FX] consists are disabled c OpSw 18 Extend the DB150 booster short circuit ...