Q: What are the differences and similarities between the LT5 module that is included as part of the BDL168 package and the Block Monitor module that is included as part of the BD4 package? A: These two devices are for all practical purposes interchangeable. Similarities – They use the same electronic schematic. Differences – They use different leds and different display configurations. The LT5 that comes with BDL168 has 5 red LEDs, four on the top row, and one on the bottom row. The Block Monitor that comes with BD4 has of 5 green LEDs in a single row. Either module can ...
What are the physical dimensions of the BD4 Quad Occupancy Detector? The longest dimension is 3.48 inches. The shortest dimension is 1.03 inches. Height at bridge rectifiers .842 inches and the height with the block monitor installed is 1.062 inches. Remember to allow for wire clearance at the screw terminal end (for the block detection wires) and also allow for vertical clearance for the DS1 and LED1 plug connections at the other end.
In this example we add some more features to complete the capabilities of the DS64 / BD4 combination. In addition to the fascia button, we utilize the remaining sensors of the BD4 to automatically select the exit route if triggered by the advancing train. For this purpose, each yard track will need a short detection section just before the yard ladder. A departing train will then trigger and set its own exit route as soon as the engine enters the detection section. To enter the yard however, the routes must still be selected manually with the push buttons.
You can automate grade crossing signal lights with block occupancy sensors. Install a BD4 to detect track occupancy as shown in the figure below. Other than removing the Op Sw35 commands from the routes used in the related article example, there is no additional programming needed for the DS64. Sensor operated occupancy detection requires that all rolling stock be equipped with resistor wheels for proper detection or that the detection section is longer on each side of the RR Crossing than the full length of a train since only the locomotive will draw current. A lighted caboose on the end of ...
Connecting BD4 to an SE8C?The BD4 is a block occupancy detection device designed as an add-on device that can take advantage of the LocoNet hosting capability of the SE8c signal decoder. It is connected this way: The installation of a BD4 is relatively simple. Looking at the BD4, you will find a 5-point terminal block on one end and two (LED1 and DS1) 10-pin (5x2) headers on the other. There are three termination areas: a) The 5-point terminal block (left) is for the interconnection between the rail power source and the rails. b) The LED1 10-pin header is ...
Q: I have a Lenz Set 100 and was wondering if I can use my DCC system and use the Digitrax signaling and detection components. What about other DCC systems?A: Yes, Digitrax detection and signaling will work with any DCC system. You will need to install a LocoNet network for the LocoNet components to communicate with each other and use a PR3 or MS100 to interface with a computer running software such as Railroad and Co.
Q: How do I use the AR1 and automatically control the turnout? I'm confused here. It is good that the AR1 controls the switching of the track power for a reverse loop automatically but it seems the turn out direction also needs auto control. Am I missing something here? Need help understanding...Please explain. A: The AR1 is handles correcting the track polarity mismatch when a reversing section is encountered by a locomotive. When the polarity inside the reverse section does not match the polarity outside the reverse section, the AR1 detects the short circuit and flips the polarity so that ...
Q: I am building a new DCC layout that will include a logging spur that is simply a single long piece of track with no loop. I want to have a train go back and forth on this track which automatically reverses when it gets to each end. While the AR1 was designed for reversing loops, can it be wired to simply reverse a train on a straight piece of track? A: Not in the way that you intend. One of the interesting problems with DCC is that we often still think in terms of DC, where the track polarity ...
How do you wire an AR1 with a BD4 so that you get block detection within the reverse loop and without the BD4 permanently detecting the AR1? It should be wired with the AR1 between the power source and the BD4. All four detection sections of the BD4 will have to be inside the reverse loop.