Reset moblile decoder to factory settings - CV08

Most Digitrax mobile decoders have a global reset function, which returns the decoder's CVs to their factory default settings.This is useful if the CV values in a particular decoder have been changed with less than wonderful results. For example, you may have accidentally set the CV value for acceleration so that the engine won't move for minutes when issued a speed command. This makes it look like the decoder is not working when all it needs is to have the CV value for acceleration reset. Many of the decoders that are sent to us for repair just need to have ...

Q: What is the exact reset procedure for a TF4? I tried both with series 3 procedure (CV8) and the other mobile decoders procedure with no success. My TF4 remains out of control. However, the white output makes the LED on my decoder testing board flicker. A: Since CV8 to 08 only works on series 3 and later decoders, it does not work on the function only decoders. TF4's CVs must be reset manually to factory values. The Factory Default Values are: CV64 000 CV61 002 CV49 000 CV50 000

Digitrax Series 3 and later mobile decoders are reset by setting CV08 to a value of 08 to reset everything or 09 to reset every thing EXCEPT the loadable speed table.Earlier Digitrax decoders require resetting each CV individually. To reset earlier Digitrax mobile decoders: Reset your decoder to the factory settings by going into program mode and manually resetting the following CVs to these values: CV01=03 CV29=06 CV03=00 CV04=00 CV02=00 CV05=00 CV06=00 If you set up loadable speed tables, you may also need to reset CV65=00 CV66=00 CV67=00 CV68-93=00 CV91=00 CV95=00    

CV08 is the factory reset CV for all FX3 decoders and also the Manufacturer ID CV for all decoders. This procedure is performed on a programming track. To reset all CV values to their factory default, program CV08 to a value of 008/x08 while the locomotive is on the programming track. To reset all CV values except for 28 step speed tables to their factory values set CV08 to a value of 009/x09. Earlier Digitrax decoders must be reset manually, CV by CV. This procedure may or may not work with other manufacturer's decoders. When you "read" the value of ...

Overview:To reset locomotive electronics to factory defaults the user must set CV08 to a value of 08. It is recommended that this procedure be performed on the dedicated service mode programming track using direct mode programming.* Note: This is the only programming procedure that we recommend using the programming track for. All other programming should be performed on the main track using Operations mode programming.Procedure:1. Place the DCC equipped locomotive on a dedicated service-mode programming track.* Note: The rails of this track should be connected to the PROG A & PROG B outputs on the DCS100 command station.2. Set the ...

Whoa!!!!!Each locomotive on your railroad has a mobile decoder which receives the command control signals from the command station and operates the locomotive motor accordingly.  The performance of mobile decoders can be adjusted by changing the Configuration Variables (CV's) of the decoder.  You can improve the speed performance of a locomotive by adjusting its start speed (CV02, V-Start), its mid-range speed (CV06, V-Mid) and its top speed (CV05 - V-Max).  You can also adjust the acceleration (CV03) and the deceleration (CV04).If the deceleration CV value you set for a particular loco is very large, this can make it look like ...

CV08 is the factory reset CV for all FX3 decoders and also the Manufacturer ID CV for all decoders.When you read the value of CV08, Digitrax decoders report back "129".To reset all CV values to their factory default, program CV08 to a value of 008  while the locomotive is on the programming track.To reset all CV values except for 28 step speed tables to their factory values set CV08 to a value of 009.Note:  Performing a factory reset will not affect the manufacturer ID and will reset the decoder's address to the factory default of 03, a 2 digit address.