CVs - Mobile Decoder Configuration Variables -> 3 Step Speed Table-CV02, CV06, CV05
You are viewing all articles in CVs - Mobile Decoder Configuration Variables -> 3 Step Speed Table-CV02, CV06, CV05 (including subcategories). To further filter by subcategory, select from below.
Why do my trains start moving at 25% throttle?You may need to adjust some CV valuesCheck the value of CV02, start voltage; the default setting is 0 (zero). You may need to adjust this value.Check the value of CV03, acceleration rate; the default setting is also 0. It is possible that the locomotive has been set for a slow acceleration rate.You can also adjust how each locomotive responds to throttle inputs by programming loadable speed tables or 3 step speed tables.If you decide to reset the decoder to factory default values , set CV08 to a value of 08 to reset the decoder back ...
Three Step Speed Table CV02 V-Start (Start Voltage) CV06 V-Mid (Mid Point Voltage) CV05 V-Max (Maximum Voltage)When you are using a throttle to control a locomotive, you will notice that as you increase and decrease the speed, the loco responds to the change in throttle settings according to the relationship between motor voltage applied and the throttle setting. This is called the throttle response curve. Decoders are shipped from the factory with a linear throttle response curve. This means that as you increase the throttle setting from 0 to full speed, the loco will look like the default curve in ...
Q: I am trying to setup 4 Kato locomotives 3 SD-70MACs and 1 C-44-9, all with DN 163K1B decoders. I am using the loadable speed tables V in the programing manual that came with my Super Chief for a starting point. I have spent a few hours with limited success. Do have any suggestions that may help simplify this process? A: Because the decoders and command control system are digital, the commands sent from the command station based on the CV settings in each locomotive are always the same. It is the locomotive mechanisms that are different. Even with three "identical" locomotives from ...
Speed stabilization is a feature that causes the decoder to run the locomotive at a somewhat constant speed according to the throttle setting. This means that if you set your throttle to 21% of total speed, the decoder will force the motor in the locomotive to maintain a constant speed at that level no matter what the track gradient or the load on the locomotive. The SD9 is an example of a US prototype that employed a load compensating type of control technology. Many modern European locomotive prototypes use some form of load compensation of the prime-mover in response to speed ...
Your locomotives look like the real thing, Digitrax LocoMotion™ System makes them run like the real thing, too! 128 speed step control. Smooth deceleration to stop before changing direction when locomotive is reversed. No sudden, non-prototypical stops! Torque compensation for the smoothest operation ever. Momentum with acceleration and deceleration settings. Set normal direction of travel for your loco. Switching speed feature for quick access to slower switching speeds. Simple 3 step speed tables are easy to set up. Advanced 28 step speed tables with 256 level resolution. Scaleable speed stabilization feature. ...
Whoa!!!!!Each locomotive on your railroad has a mobile decoder which receives the command control signals from the command station and operates the locomotive motor accordingly. The performance of mobile decoders can be adjusted by changing the Configuration Variables (CV's) of the decoder. You can improve the speed performance of a locomotive by adjusting its start speed (CV02, V-Start), its mid-range speed (CV06, V-Mid) and its top speed (CV05 - V-Max). You can also adjust the acceleration (CV03) and the deceleration (CV04).If the deceleration CV value you set for a particular loco is very large, this can make it look like ...
A speed table is a list of numbers, one number for each speed step. Many operators customize their locomotives by adjusting the CV's for Vstart (02), Vmid (06) and Vmax (05) to set the throttle response characteristics for each locomotive. This is known as a three-step speed table It is also possible to create a more complex speed table, either with 14 or 28 steps that specify the exact percentage of full power sent to the motor when the throttle is set to that speed. Speed tables can be set up for 14 or 28 speed steps, but not for ...
How do I get all the engines of a consist to run at the same speed? I have 3 engines with DH163A0 decoders and one with a MRC sound decoder. All units have the same top speed, but the unit with the MRC decoder starts and accelerates more quickly. Getting a group of locomotives to operate at the same speed can be a challenge. Experience has proven that it is best to work with the slowest locomotive and bring the other locomotives into agreement with that engine. Since the others appear to be in general agreement, it would be the ...