DT602 Throttle Option Settings
|
Throttle ID# |
Option Name |
Factory State |
|
ID01 |
Ballistic Knobs With Ballistic tracking, the faster you increase or decrease the throttle knob the faster the data changes in the throttle. When Off the speed step increase is per encoder notch. |
on |
|
ID02 |
Key clicks Off disables clicks for key press and encoder changes. |
on |
|
ID03 |
Duplex RF allow Off will turn off Duplex Radio capability. |
on |
|
ID04 |
IR allow Off will turn off IR capability. |
on |
|
ID05 |
Fast Clock show On will show fast clock. |
off |
|
ID06 |
24Hr Clock mode On changes the clock mode from 12Hr to 24Hr. |
off |
|
ID07 |
Fclock Alarm Enables a Fast Clock Alarm to be set with audible beeps. |
off |
|
ID08 |
Enc=> LCD wake When ON the display will restore by turning encoder knob. |
off |
|
ID09 |
FnKEY=> LCD wake When On the display will restore by function key presses 0-9. |
off |
|
ID10 |
Expanded Cmds On will allow the throttle to acquire, control and release of Expanded slots. Off will prevent the throttle from using addresses in Expanded slots. |
off |
|
ID11 |
F2 Key Static On enables F2 to operate with key press on and key press off. Off enables F2 to be momentary. |
off |
|
ID12 |
Spare1 |
off |
|
ID13 |
Duplex PD 20min Off enables Power Down without Duplex activity 5 minutes. On enables Power Down without Duplex activity 20 minutes. |
off |
|
ID14 |
Duple RX always On enables Duplex RX on always. (This can increase battery drain) |
off |
|
ID15 |
Max LCD brite Level: 0 = Minimum Screen Brightness level. 6 = Maximum Screen Brightness level. |
5 |
|
ID16 |
Min LCD brite level: 0 = Minimum Screen Brightness level after hold delay. 6 = Maximum Screen Brightness level after hold delay. |
3 |
|
ID17 |
Keypad brite level: 0 = Minimum Keypad Brightness. 4 = Maximum Keypad Brightness |
1 |
|
ID18 |
LCD brite hold delay: 0 = Screen will not Dim. 1 = Min LCD brite level after 8 seconds. 2 = Min LCD brite level after 16 seconds. 3 = Min LCD brite level after 18 seconds. 4 = Min LCD brite level after 23 seconds. 5 = Min LCD brite level after 28 seconds. 6 = Min LCD brite level after 32 seconds. 7 = Min LCD brite level after 37 seconds. |
2 |
|
ID19 |
LCD pwr save delay 0 = After LCD brite hold delay the LCD screen will turn off. 1 = After LCD brite hold delay the LCD screen will turn off after 15 seconds. 2 = After LCD brite hold delay the LCD screen will turn off after 20 seconds. 3 = After LCD brite hold delay the LCD screen will turn off after 25 seconds. 4 = After LCD brite hold delay the LCD screen will turn off after 30 seconds. 5 = After LCD brite hold delay the LCD screen will turn off after 35 seconds. 6 = After LCD brite hold delay the LCD screen will turn off after 40 seconds. 7 = After LCD brite hold delay the LCD screen will turn off after 45 seconds. |
2 |
|
ID20 |
New Loco steps 0 = 28 speed steps 1 = Reserved 2 = Reserved 3 = 128 speed steps 4 = 28 speed steps Advanced 5 = Reserved 6 = Reserved 7 = 128 speed steps Advanced |
3 |
|
ID21 |
LnMSG beeps: When On, an audible beep will confirm LocoNet command received. |
off |
|
ID22 |
Spare2 |
off |
|
ID40 |
Set Factory Default On reverts DT602 back to Factory Default |
off |