Remove the 8 pin dummy plug from Lifelike Proto 2000 light board.Before installing the decoder in the locomotive, unsolder the yellow wire from pin 2 and re-solder it to pin 3 (empty pin) on the decoder harness plug board.  We strongly recommend that you mark the decoder and/or harness so that you will remember that you have modified it.  If you use the decoder and/or harness modified in this manner in a different locomotive, your lights will not work correctly. Plug the decoder and harness into the light board in the locomotive.Program CVs as follows:  CV33 = 001, CV34 = ...

I'm trying to install a DH123D decoder in a Life like P2K PA loco and make the mars light work. HELP! Because the DH123D is a two-function decoder (front headlight, rear headlight), it may not be the best decoder choice for this locomotive. In practice, some PA's had only one headlight, thus there would be no Mars light. The DH123D would be an appropriate choice for those locomotives. Typically, eastern railroads would just have one headlight; think Pennsy and Southern Railway. Western railroads, because of higher train speeds, often used warning lights such as the Mars Light or Pyle Gyra-Light; ...

Life-Like Proto 2000 locomotives with number board lights have the number board bulbs wired to their 8-pin DCC plug using pins 4 and 5. This causes no problems with DC operation but causes a path from the rail pickup to the gray motor lead when a decoder is installed resulting in erratic operation and decoder failure.This is a known problem in the Proto 2000 GP60, SD60M and LifeLike GP38-2.  The DH165L0 uses a current limiter set to control one incandescent bulb on the front (FOF) and one on the rear (FOR) and putting the removed number board bulb on either ...

This installation procedure is for the DIGITRAX DH166/DH126 decoder. Alternatively, you can use a Digitrax DN166 in this installation. If you use the DN166 the installation will require fewer engine modifications because of the smaller physical size of the decoder.Note any decoder of smaller physical size can be used in this installation.  DN136D, DN166, DZ126, DZ126, DZ146 are all possibilities. After removing the shell from the locomotive chassis, note the color and location of each of the various wires.  All connections must be soldered with rosin core solder and insulated with shrink tubing.We will locate the decoder in the forward ...

Do you have a reference for wiring Proto 2000 older geeps with a decoder (not necessarily sound)? We actually have several Life-Like Proto's sitting around for conversion to DCC, including an older GP-18, older FA's and such that date back to the days when DCC was just a twinkle in AJ's eyes. Overall, converting these locomotives will be fairly easy but there are a few things to watch for. Make sure that the decoder has enough capacity to match the current demands of the locomotive mechanism.  You must measure the stall current of the locomotive to determine this.   Make ...

There is a potential problem using the DCC socket on the Life Like Proto2000 S-1. While the trucks and track pick-ups are isolated from the frame, there is a brass grounding lug attached to the motor's lower brush cap which makes electrical contact between the lower motor brush and the frame.  As a result if the wheels come in contact with the frame a short occurs and the decoder may be damaged! We recommend one of two work-arounds. 1) If you choose to use the 8 pin DCC plug, isolate the bottom motor brush from the frame of the locomotive ...

"I had two Proto 1000 RDC's that I wanted to convert. After opening up the first one, I did what I usually do, yanked out all the circuit boards and such, threw them over my shoulder and commenced to hardwiring the decoder into the unit. Everything went fine, and I took it with me to a friend's railroad to enjoy what I had done. After I got there and played a bit, my friend commented that wasn't it neat that the Proto 1000 series has wiring connections on the circuit board in the locomotive, making things considerably easier. Wiring points?" ...

Setting Up a Mars Lights with the PR1To program the decoder for Mars Light or other "single" output applications, follow these steps:1. Go to the Digitrax Decoder Programmer2. Select FX Set up3. Choose the function that you want to be the Mars Light4. Select "Mars Light"5. Click "OK"6. When you are back in the main screen click "Send"

Q:  I have a DH163D decoder. How do I program it so the Mars light works? A:  Any function output on Digitrax FX decoders can be set up for any FX effect by programming its associated FX CV to the appropriate FX CV value. For example, if CV52 (the FX CV for F2), is programmed with a CV value of 034, the violet wire F2 function output will be a Mars light when F2 is turned on for this decoder address and the decoder's direction is forward.

My son & I have PROTO 1000 Diesel EMD F3A-B Sets. The powered locos are equipped with an eight-pin plug for easy decoder installation. Our problem is that we've been looking through books & have no idea what sound card & speakers we are going to need that corresponds with these type of locomotives. I was told that they would need sound cards that are from the "Early Diesel" era. If this is true, please tell me what sound cards,speakers & wires do we need to make this happen? We are fond of F-units, and the Proto 1000 F-units are ...

I have this N-scale Proto A/B unit. I went to install the decoder in the A unit to the headlight, its an LED. My question is that once it was wired up and place on the track, I hit my headlight function and the light lit up then burnt out. This is my first wired decoder I ever installed with a head light. Can you tell me how to properly wire the led headlight to the DZ123 decoder so the light doesn't burn out? In looking at the DZ123 Decoder sheet, it suggests that I check the Decoder Manual for ...

Board Replacement Decoder for Walthers Proto GP20 and similar locos

Many locomotives feature warning lights that are designed to make a train more visible to the general public. FX Functions are function outputs that incorporate 4 FX generators for prototypical lighting effects such as Mars lights, ditch lights, Pyle Gyra-lights, rotating beacons, single and double pulse strobe lights, and random flicker.

DCS50 Zephyr can control Functions F0 - F8. Most DCC mobile decoders have function outputs that you can use to control lamps, LEDs, sound, smoke generators and other on/off devices installed in your locomotives. Most locomotives made today come with a head light and sometimes with a rear light, too. With DCC, these are controlled by the decoder’s function outputs. You can also install additional DCC controlled lighting such as cab lights, Mars lights, ditch lights, rotating beacons and others on your locos. The addition of these functions can add to the fun and realism of your locomotives.You must have ...

Configurable strobes are controlled with CV49 & CV50. CV49 controls the White Lead   CV50 controls the Yellow Lead The value programmed for each CV consists of 2 digits, the first digit controls the conditions under which the light will be active.1x=Reverse, if 1 is the first digit then the light will be on when the locomotive is in reverse2x=F0 Qualified, if 2 is the first digit then the function will be active when F0 is on and off when F0 is off4x=Direction insensitive, if 4 is the first digit then the function will be On in either directionThe second ...

This note addresses the installation of an H0-Scale wired decoder into Bachmann Plus ABA F-7s; it calls for using a DH140, which has been retired.  Current decoders such as the DH123 or DH163 or similar wired decoders can be used. Just finished up doing a few HO Bachmann Plus F7's, ABA's to be exact. Thought maybe some of you might be interested in how the DCC conversion went on these.They are an easy conversion!1.  The full stall current for these ranged from 500-700 ma for each loco . I selected Digitrax DH140 for the A units and a DH120 for the B ...

Decoders with FX function features have 4 user configurable, independent special effects generators. All current production Digitrax Decoders use FX3 functions so this article is not applicapable to these decoders. CAUTION: Decoders with FX3 function generators use different CVs to control the decoder outputs. All current production Digitrax decoders use FX3 function CVs. Before using these CVs to program your decoders make sure that they are FX and not FX3 decoders.The Real FX effects are set up by programming CV values as described below.F1/F2 NOTE: If using DH142, DN142, DN141K2, DN149K2 series decoder, when F1 is set up for FX, ...

When you click on the "FX-Setup" button a second menu screen appears which contains the special light effects for the FX decoder. If the decoder you are programming is not capable of FX effects, this section will not apply to your situation.On this screen we have access to F0 Forward Light, F0 Reverse Light, F1, F2, F3 & F4. The programming directions and choices are the same for each function. The pull down field to the right of this shows you which effect is assigned to that particular function. The following is a list of choices: No effect, normal function ...

  Digitrax UT4D Throttle Operating Instructions by Dan Bourque   v1.0 Selecting a locomotive or consist 1.         Dial the 4-digit locomotive address into the “LOCO ADDRESS” dials             - For a consist, the address will normally be the lead locomotive             - For a 3-digit locomotive number, use “0” for the first digit 2.         Press the “SEL” key, the ST light on the throttle should flash green 3.         Move the direction selector on the throttle to either “R” or “F” 4.         Move the speed knob until train moves 5.         For headlight, press the “F0” key (“F3” will ...

DCS50 Zephyr can control Functions F0 - F8. Most DCC mobile decoders have function outputs that you can use to control lamps, LEDs, sound, smoke generators and other on/off devices installed in your locomotives. Most locomotives made today come with a head light and sometimes with a rear light, too. With DCC, these are controlled by the decoder’s function outputs. You can also install additional DCC controlled lighting such as cab lights, Mars lights, ditch lights, rotating beacons and others on your locos. The addition of these functions can add to the fun and realism of your locomotives.You must have ...

Q:  Using Digitrax systems to program an MRC AD310 decoder is especially confusing because the MRC Command 2000 uses several "switches" and "levers" rather than standard CV numbers. A conversion chart for the 10 possible MRC engine addresses would be a wonderful help to us old-timers. A:  The documentation available from the manufacturer of this decoder is incomplete. Many older decoders such as this one are not able to recognize all the digital packets in use by more modern DCC Systems. What we have learned is the MRC AD310 is: Programmable up to 127 (1~127) locomotive addresses Programmable for either 28 or ...

Configurable strobes are set up using CV's 49, 50 and 61. Configurable strobe function leads can be programmed with a limited number of simulated lighting effects similar to FX effects but without as many options. Configurable strobes are offered in those few Digitrax decoders where there was not enough "code space" to provide full FX features.CV49 controls F0 Forward, the white function lead. CV50 controls F0 reverse, the yellow function lead.CV61 enables the configurable strobe operation.To set up configurable strobe lights:1. Program CV61 with the CV value "01" to enable configurable strobe operation.2. Program the CV value for CVs 49 ...

Decoders with FX3 features have 8 user configurable, independent special effects generators.  All current production Digitrax Decoders use FX3 function features. These are set up by programming CV values as described below.  If your decoder is not a Series 3 decoder, please check the spec sheet to determine which type of functions it supports.FX3 functions incorporate FX generators with additional dynamic and static qualifiers.  FX3 functions are fully remappable so they can be controlled by any function key on your system.  A master light switch can be set up to turn off all lights on a locomotive. Functions associated with advanced ...

  Digitrax UT4 Throttle Operating Instructions by Dan Bourque     Selecting a locomotive or consist 1.         Dial the 4-digit locomotive address into the “LOCO ADDRESS” dials             - For a consist, the address will normally be the lead locomotive             - For a 3-digit locomotive number, use “0” for the first digit 2.         Plug the throttle into any receptacle on the layout fascia (e.g. Digitrax UP5) 3.         Press the “SEL” key, the ST light on the throttle should turn green 4.         Move the direction selector on the throttle to either “R” or “F” 5.         Move the ...

Digitrax decoders have outputs that can control lamps and other on/off devices installed in your locomotive.  These are called functions.  Functions are things like: lamps, sound units, smoke units, etc. All Digitrax decoders are equipped with two or more function outputs that are used to turn functions on and off.Decoder function outputs can be:1.   Leads (wires) attached to the decoder that are used to hook up external functions.  See Table I below for wire color codes used on Digitrax decoders.or2.   Pre-wired function outputs that hook up by just plugging in the decoder. This is the case for decoders that ...

Will the PR3 and SoundLoader software work on systems with specifications other than those listed in the PR3 manual? The beta testers have reported that the PR3 with SoundLoader software, DigiMon software, and IPL software have been found to work on many desktop and laptop computers running Windows 2000 and Windows XP with Processors as slow as 450mhz, Ram memory as little as 128mb, and USB 1.1 Ports. The beta testers cannot confirm that every computer with the above limitations will function properly with the PR3 and SoundLoader software.

The UP1 Universal Panel was manufactured between 1995 and 2000.

Empire Builder was manufactured from 1998 to 2000.  It was offered with a DT100 throttle.

Chief was Digitrax third commercially produced starter set.  It was manufactured from 1998 to 2000.  It included:A DT100 throttleA DCS100 command Station Booster

This application note shows how you can use your Digitrax PR2 Programmer with the USB Port on your computer. The PR2 has been replaced by PR3 Programmer and Computer Interface.  PR3 offers USB connectivity.The PR2 Programmer is a serial device that connects to a computer via a 25pin serial port. Serial ports are not available on most computers in current production. USB ports are more widely used today. The Digitrax PR2 Programmer can be connected to a USB port by using a USB to Serial RS-232 DB-25 Adapter Cable. Caution: Not all cables on the market will work. One that ...

The MS100 LocoNet Interface is a serial device that connects LocoNet to a computer via a 25pin serial port.This application note shows how you can use your Digitrax MS100 computer interface with the USB Port on your computer.  Serial ports are not available on most computers in current production. USB ports are more widely used today.  The Digitrax MS100 LocoNet interface can be connected to a USB port by using a USB to Serial RS-232 DB-25 Adapter Cable.  Digitrax recommends the PR3 for interfacing your USB equipped computer with LocoNet.Caution: Not all cables on the market will work. One that ...

Note: If the PR3 driver installation process fails, you will have to uninstall the VCOM USB driver before attempting reinstallation. We suggest using a utility called USBDeview for this purpose.  It is available for download from: http://www.nirsoft.net/utils/usb_devices_view.htmlThe process is simple, run the USBDeview program, location the VCOM driver in the list and right click to uninstall. Disclaimer The software is provided "AS IS" without any warranty, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The author will not be liable for any special, incidental, consequential or indirect damages ...

By Zana & A.J. IrelandThis clinic is titled Digital Command Control: The Wave of the Future. Recently, I was asked the question: "DCC has arrived and is the technology of today, everybody's using it so, why don't you change the title of your clinic?" My answer is that digital command control is still evolving rapidly. Today's digital command control is moving beyond the basic NMRA DCC Standards and RPs to encompass many new technologies that will compliment and enhance the basic things we can do with the track format defined by the NMRA. It's an exciting time for model railroaders ...

By Zana & A.J. IrelandThis clinic is titled Digital Command Control: The Wave of the Future. Recently, I was asked the question: "DCC has arrived and is the technology of today, everybody's using it so, why don't you change the title of your clinic?" My answer is that digital command control is still evolving rapidly. Today's digital command control is moving beyond the basic NMRA DCC Standards and RPs to encompass many new technologies that will compliment and enhance the basic things we can do with the track format defined by the NMRA. It's an exciting time for model railroaders ...

The following CV set up simulates prototypical ditch lights that are on steady when running and alternately flashing when the horn blows. The ditch lights will be on when the engine is running, when you simulate blowing the horn by going into function mode and pressing F2 the ditch lights will flash on alternate sides of the loco. Note, the F2 key on Digitrax throttles is set up as a non-latching function so that the function assigned to F2 will be "ON" as long as you hold the F2 key down and will go "OFF" when it is released. Follow ...

I have a DH165AO decoder and Sound Bug and am installing the decoders into an Athearn SD70 Locomotive.The motor controller works and the sound as well. However, I am unable to get the lights to work. I connected the wire leads exactly as they where on the Athearn light board. Athearn uses twin forward and rear 1.5 volt lights yet the DH165AO will not power the bulbs. It will power one bulb at either end but not two. The single bulb setup glows very brightly but for a short time. So I tried using the 47 ohm resistor in parallel ...

What's the best method to handle structure and street lighting with a DCC layout? If I put in bus wiring for my lighting can it interfere with the DCC signal? Unless you have stationary decoders that control the structure and street lights, there is no need for connecting these lights to your DCC wiring. In fact, doing so will add additional power consumption without any of the advantages of command control. These additional power consumers take away available power for your locomotives, controlled cars and stationary decoders. Should I use a completely different power source like an old power pack? ...

Athearn Genesis SD70s came factory equipped with a Digitrax designed light board. The board is NOT a DCC decoder. If you want to add a decoder and have alternating ditch lights the following steps are recommended: 1 - Remove locomotive shell; 2 - Remove dummy nine pin plug from wire harness and insert Digitrax DH163D on the harness; 3 - Remove the wires of one of the ditch light bulbs from F1N and F1P and solder them to F2N and F2P; 4 - Program CV51 to 106, CV52 to 107 and CV63 to 40. 5 - Reinstall locomotive shell.F2 on ...

There is an error in the BD4 Instruction Sheet, 2004 version.As a result of this error, BD4 shows no status light and no detection lights.  The solution is to connect pin 10 of the DS1 on the BD4 to a system ground such as the AX1 terminal of the DS64, Ground on the booster terminal, etc. This connection was not shown on the original instruction sheet for the BD4.

I'm looking to wire Tortoise switch machines on a DS64. When the track switch is thrown I want to power 1 color light (non-LED). When the track switch is closed, power a different colored light. Is this possible using the DS64 inputs or the Tortoise connections? The DS64 does not have separate connections for indicator lights for trackside or for a control panel. However, indicator lights can still wired to work with the DS64. Tortoise or other slow motion swith machines can be wired in two different ways. If using LEDs, a two leg, bipolar LED can be connected in ...

Flashing ditch lights can be set up with several CV's. Using 1.5 Volt Bulbs or LEDsIf you use 1.5 V bulbs, you must install a current setting resistor with a minimum value of 100 ohms for each bulb.Typically a 560 ohm 1/4 watt resistor works well for a grain of rice bulb and a 250 ohm 1/4 watt resistor works well for a grain of wheat bulb.Lower resistance values will increase the lamp brightness. If you use LED's be sure the polarity is correct when you hook them up & install a current setting resistor for each LED. Typically a ...

The headlights of my locomotive aren't acting properly. If you can’t control the operation of the lights in your locomotive with the DT400 (in default 128, or 28 speed step mode), be sure that the decoder is programmed in advanced 28 speed step mode. Do this by programming CV29 with a decimal value of 06.

Wiring lighting without burning out bulbs on the first try. Need some info on which bulbs and boards need drop resisters installed and why. The new DH165 series have eliminated the mystery since they work with either LED's or with conventional lamps without adding resistors.

Many thanks to Bob Dattore for this application note!This app note details using a DN142 decoder for the installation.  This decoder is no longer in production but the following decoders would work as well:  DN135D, DN163, DZ123, DZ125, DZ143.  Any decoder that is small enough to fit could be used.The Problem:  Atlas RS1's (and RS3's & RSD4/5's) are hard to install Digitrax decoders in. There is no easy drop-in or light board replacement with back-emf capability.I have installed several Atlas Dual Mode decoders in these popular hard to fit narrow, low hood diesels with ease, by replacing the original light ...

The SE8C can drive position light type signals such as those used by the Pennsylvania Railroad and the B&O RR and the N&W RR. Leads from the signals can be soldered directly to the pads on the Signal Mast Base (the Terminal Strip Mounting Kit can also be used for interfacing your signals with the system.)You can use either common anode or common cathode signals.  We recommend that you use either all common anode or all common cathode signals on your layout for consistency in the set up procedure on your layout. If you are using the terminal strip option ...

You can automate grade crossing signal lights with block occupancy sensors. Install a BD4 to detect track occupancy as shown in the figure below. Other than removing the Op Sw35 commands from the routes used in the related article example, there is no additional programming needed for the DS64. Sensor operated occupancy detection requires that all rolling stock be equipped with resistor wheels for proper detection or that the detection section is longer on each side of the RR Crossing than the full length of a train since only the locomotive will draw current. A lighted caboose on the end of ...

UT4 Function Control Keys and How they WorkThere are 8 physical keys used to control functions F0-F12 on the UT4 throttle. F1 through F6 and F7-F12 share the same keys.  You will see F1-F6 in black print and F7-F12 in blue print to remind you that you will need to use the SHIFT key to access F7-F12. To use functions F7-F12 you must press and hold down the SHIFT key on the lower left row of the throttle as you press the F7 through F12 keys to activate any functions available on those functions. All the UT4 functions work like other Digitrax throttles. ...

One of the basic problems encountered with command control systems is when things simply are not working.  Period.  Even after vigorous exhortation on your part, and perhaps even some enthusiastic train table banging, nothing is running.  At this point, it is time to gather your wits and your patience for a debugging session.   The first step to determining how to proceed is to determine if the problem with the electronics or with the layout?  The tendency is to blame the electronics, after all it is a black box.  But don't jump to conclusions so quickly! Be patient and follow the ...

This application note concerns the DA120 deocder, which began production in 1997 and was discontinued around 2000. The DA120 decoder that is being shipped with the Atlas locomotives has certain variables that are available for programming. These guidelines are provided for those who are using the Wangrow or Lenz systems for programming the DA120 decoders.The following variables were selected by Atlas to be offered in the DA120. These CV's are available to be programmed on the DA120:    * CV01 - Address    * CV02 - Start Voltage    * CV03 - Acceleration Rate    * CV04 - Deceleration Rate    * CV05 - Maximum ...

Digitrax Complete Train Control By Zana & A.J. Ireland Digitrax Complete Train Control makes reliable, realistic train operation and simplified layout wiring a reality. Digital Command Control is incorporated within the Digitrax system to let you control multiple trains independently on the same section of track without blocking. In the real world, engineers control the speed and direction of real trains. Engines operate under their own power independent of the track. Each engine has its own motion characteristics like how fast it speeds up (acceleration) and how long it takes to slow down (deceleration). A locomotive's performance is influenced by ...

The DCS240 uses different combinations ofthe PWR, PROG, NET, TRACK STAUSand USB indicator to provide a visual indication.  The indicators can show what mode the DCS240 is in as well as errors and indications.   Indications Meaning PWR GREEN winking off every 3 seconds as a “Heartbeat”  The DCS240 is powered on in Command Station Mode, Normal Operation Mode.  PWR RED winking off every 3 seconds as a “Heartbeat”  The DCS240 is powered on in Booster Only Mode, Normal Operation Mode.  PWR off blinking on GREEN or RED every 4 seconds  The DCS240 is in SLEEP mode. (GREEN = Command Station Mode) ...

Q: My front and rear lights on a steam locomotive (hard wired decoder installation) are connected in reverse. When the locomotive is going forward, the back up light comes on. When the locomotive is going in reverse, the forward light comes on. Can I reverse the lighting effects though programming the decoder or must I disassemble the locomoitve and physically swap the wiring to the lights from the decoder. A: Yes, you can do this with using function mapping in any Digitrax decoder Series 3 or later. If you have an earlier version decoder installed, you'll need to re-wire the ...

Kato N-Scale GG1 steps needed for the DN163K1D decoder Carefully remove the locomotive’s shell and light board retainer from the frame. Notice the orientation of the light board inside so that you can install the new decoder in the same orientation. Carefully remove the factory light board by sliding it toward the back of the locomotive and out from under the forward frame notches. Then gently lift the board out of the frame. Be careful not to bend or damage the motor tabs. Carefully remove the motor tabs from the factory lightboard. The motor tabs attach to the board with ...

The DZ125 is set up at the factory to control two function outputs. The DZ125 is configured to control the forward and reverse lights on the locomotive through the white lead and yellow lead using Function 0 (F0F-forward and F0R-reverse) for directional lighting. Both function outputs can be easily set up with Digitrax FX3 lighting effects or as standard on/off functions with the following operational qualifiers: 1. Forward or Reverse direction of travel, or 2. Whether F0 is on or off, or 3. Both direction of travel and whether F0 is on or off, or 4. Whether the locomotive is ...

The track plan of the model Kelana Jaya Rail Line is shown below: Included in the model is the double track mainline with crossovers, two elevated stations with center platforms, one at-grade station with outside platforms and two underground stations, also with center platforms. The storage yard, maintenance yard and reversing loop at one end of the system and the four track stub terminal at the other end of the system are also modeled. The yard, station tracks, crossing loops and distances between stations are all scaled to hold trains no larger than three cars. The layout is designed to ...

Digitrax uses CV33-CV46 to handle remapping according to published standards.The CV values that are permitted for function remapping are limited to 8 bits, a maximum value of 255. Therefore only 8 functions can be mapped to each function key.Function remapping is easy! Just follow these simple steps:1. Locate the row for the Throttle Function Key [chart below] that you want to use.2. Locate the column of the Function Lead Color (number) you want to control.3. Note the value at the intersection of the row and column.4. Program that value into the the CV listed next to the Throttle Function Key. ...

The image above shows the “M-10000 Coach Car B” for the N scale Con-Cor M-10000, which is the 1st car behind the loco. If you look closely, you can see the holes in the underbody, above which a speaker can be mounted for a sound decoder installation. The recommended Digitrax sound decoder would be the Digitrax SFX0416, but to use this decoder, one or more of the seat sections as shown below will need to be removed. There is a pocket that is designed for a speaker above the underbelly and under the center section of seats. The speaker that comes with ...

1) Remove locomotive shell following Roundhouse instructions.2) There are two large diodes, one on each side of the rectangular light board. Remove them.3) The two LEDs are wired to this light board, one on each side with black and gray wires on each LED. Reverse the black and gray wires on the board from each LED (gray to where black was and black to where gray was.4) Remove the dummy eight pin plug and insert the eight pin DCC medium plug of a Digitrax DZ1xxPS decoder with the orange wire going to #1 on the light board.5) Reinstall locomotive shell.FAILURE ...

This installation covers how to install a Digitrax decoder with wires in any Athearn HO locomotive.  Use either our DH123 (headlight functions only) or DH163 (headlights plus additional functions) for this installation.*** Note: This installation is based on installing a Digitrax wired decoder in an Athearn Dash 9-44CW. The process is similar for any Digitrax mobile decoder with wires. The instructions are also easily applicable for any Athearn locomotive.These instructions assume that you have already run the loco and have established that it is working properly before beginning installation. Remember, installing a decoder in a locomotive will not improve its ...

IPLING From time to time the latest DT602 family throttle firmware will be updated and will be posted on the product support page.  These updates may slightly modify the DT602's operation, based on customer feedback/requests and priority support issues discovered. If you are happy with the operation of your DT602, and have no issues or new features you may want, it is not required to perform an available update. All DT602 family throttles should only be firmware updated or IPL'd while plugged directly into a working LocoNet. The Digitrax provided DMF file for field updating DT602's can be used for IPL of any ...

FX3 decoders have motor isolation protection. If the decoder senses that the motor is not isolated, it will not run the motor. In this case, you will be able to control the loco’s functions but the motor will not work.FX decoders will blink the loco's lights when power is first applied to the decoder to warn you of a short circuit in your installation. If you see the lights blinking, immediately remove the loco from the track, locate the short circuit and correct the problem before proceeding. Do not leave the loco on the track with blinking lights because eventually, ...

The Athearn N-Scale P59PHI was not designed for a plug 'n play or board replacement installation therefore, a wired installation will be necessary. This installation is straightforward if you follow the instructions provided below. There is plenty of room inside the locomotive for this installation. See the Digitrax Decoder Selector on our home page to determine which current production decoder is recommended for this installation. Athearn N-Scale P59PHI Installation Instructions for Digitrax Decoders:1. Remove the locomotive's shell. Note which end of the frame is the front and which is the back.2. Remove the light board that is installed on the ...

Our thanks go to Digitrax operator Aksel Suarez of Chesapeake, Virginia for sending this tip on how to install a Digitrax decoder in the Walthers GP15, called by some prototype railroaders a "Geepette" or "Cheep Geep". Use a DH165A0 decoder to replace the existing light board. Remove the plastic clips that hold the wires to the light board. Once the light board has been removed, place a piece of electrical tape on the metal frame to isolate the decoder from the frame and prevent a short circuit. The wires on the locomotive to the motor and lights do not follow ...

Testing for Tower 55 DCC Equipped Locos after 4 Digit address programming:Note these instructions are the same for both DCS50 Zephyr and DCS51 Zephyr Xtra1. Press the LOCO key on the DCS50. (The LED display should begin flashing)2. Enter the 4-digit address that was programmed in the procedure above using the numeric keypad. (The LED display should be flashing “####” with the # symbols replaced with the 4-digit address that was keyed in)3. Press the LOCO key on the DCS50. (The LED display should display “####” solid and the locomotive sounds should start up)4. Select FORWARD with the direction knob ...

The DN163A0 is set up at the factory to control six functions. The unit is prewired with two golden-white LEDs set up for directional lighting as F0F/F0F+ for the front light and F0R/F0R+ for the rear light. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) can be used by soldering a wire from the pad for the function you wish to use to the lamp (or other function) you wish to control. The wire colors indicated are the standard color code used in the industry (you can use any color you like). These colors are important if you ...

The DN163K1D is set up at the factory to control six functions. The unit is prewired with two white LED's set up for directional lighting as F0F/F0F+ for the front light and F0R/F0R+ for the rear light. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) can be used by soldering a wire from the pad for the function you wish to use to the lamp (or other function) you wish to control. The wire colors indicated are the standard color code used in the industry (you can use any color you like). These colors are important if you ...

Is this part of the instructions sheet?  If so, we don't need it here?  ZIThe DN163K2 is set up at the factory to control six functions. The unit is prewired with two golden-white LEDs set up for directional lighting as F0F/F0F+ for the front light and F0R/F0R+ for the rear light. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) can be used by soldering a wire from the pad for the function you wish to use to the lamp (or other function) you wish to control. The wire colors indicated are the standard color code used in the ...

Kato N-Scale DD51 steps needed for the DN163K1D decoder Carefully remove the DD51 locomotive shells (3) and gray plastic light board retainer from the frame. Carefully remove the factory light board by sliding it toward the back of the locomotive and out from under the forward frame notches. Then gently lift the board out of the frame. Be careful not to bend or damage the motor tabs. Place one or more layers of Kapton tape on the frame underneath the forward frame clip. Carefully remove the motor tabs from the factory light board. The motor tabs attach to the board ...

1. Carefully remove the locomotive's shell from the frame. Notice the orientation of the shell for reinstallation. 2. Carefully remove the plastic light shroud by gently prying up the tabs on either side of the frame and lifting the plastic piece off the frame. 3. Slide the factory light board forward to release it from under the clips on the locomotive frame. Be careful not to distort the frame clips as you slide and lift the light board off the frame. 4. Place the small piece of kapton tape provided with the decoder on the loco frame, wrapping it around ...

Characteristics Controlled by CV61:Some Digitrax Decoders use CV61 (one of the manufacturer specific configuration variables) to give you the following options:  Non-Directional Headlight Operation, Transponding Enabled or Disabled, & Split Phase Motor Drive for Märklin AC and Lionel Type motors.The look up table below shows the effects of different CV values that you can program into CV61.  CV values are shown in hex & decimal are the same in this case.TABLE 61: CV61 Values CV 61 Value Non-directional headlights Transponding Split Field Motor/AC 00 No No No 01 Yes No No 02 No Yes No 03 Yes Yes No 04 ...

The DN163A1 is set up at the factory to control six functions. The unit is prewired with two golden-white LEDs set up for directional lighting as F0F/F0F+ for the front light and F0R/F0R+ for the rear light. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) can be used by soldering a wire from the pad for the function you wish to use to the lamp (or other function) you wish to control. The wire colors indicated are the standard color code used in the industry (you can use any color you like). These colors are important if you ...

DN163A0 is a board replacement decoder for Atlas N-Scale GP40-2, GP38 U25B, SD35, Trainmaster, B23-7 and several others. Shown here is an installation in a GP40-2. 1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the light board inside so that you can install the decoder in the same orientation. 2. Carefully remove the plastic light shroud at the front of the loco and loosen the frame screws enough to allow the removal of the light board. Lift the board out of the frame. 3. Install the decoder, square CPU to the top, between the frame ...

  I have a 14x24 foot room with a shelf layout on two levels. 1st level is about 24 inches with two main lines and some industries, a moderate freight yard, moderate intermodal facility and passenger station. The second level is 18 inches and will contain one and two main lines with mostly industries. This would qualify as a "medium to large" model railroad. I would like to have 1-5 operators with 2-10 trains running at one time as permitting. At least four Universal Panels would give all operators full access to LocoNet as necessary. At least one UP each ...

The DZ125IN is set up at the factory to control two function outputs. The DZ125IN is configured to control the forward and reverse lights on the locomotive through the white lead and yellow lead using Function 0 (F0F-forward and F0R-reverse) for directional lighting. Both function outputs can be easily set up with Digitrax FX3 lighting effects or as standard on/off functions with the following operational qualifiers: 1. Forward or Reverse direction of travel, or 2. Whether F0 is on or off, or 3. Both direction of travel and whether F0 is on or off, or 4. Whether the locomotive is ...

Q:  Your recommendation is to have a DB150 booster at no more than 50 foot intervals. Will one booster handle all track in that 50 foot area, i.e. a passenger terminal throat with many turnouts and switches? A:  The "50 foot intervals" applies to the maximum distance which boosters can be located from each other. This is a conservative recommendation.  You should consider how much power will be consumed in a district when locating boosters around the layout. If your power district is a single track railroad stretching over hundreds of feet of linear distance, boosters should be placed at 50 ...

If you are NOT plugged into a LocoNet port1. Use the 4 rotary address selector knobs on your UT4 to dial up the 2 or 4 digit address of the locomotive you want to run.  To enter a 2-digit addresses, set the first two selector knobs to 0 and enter the two digit address on the 2 address selector knobs on the right hand side of the throttle (for example 0025).2. Plug the UT4 into any LocoNet port and automatic selection occurs.3. A Green Status light confirms that selection has been done successfully - You’re off and running!4. A Red Status light means the loco is ...

To Test LocoNet Cables With an LT11. Unplug the wire harness from the LT1.2. Plug one end of the LocoNet cable you want to test into the LT1.Note: When making your own LocoNet Cables, it is important to make them in a consistent manner. At Digitrax, the white wire is always on the right side of the plug when the plug is viewed with the clip at the top.3. Connect the other end of the LocoNet Cable being tested to any powered Digitrax Booster’s LocoNet Port A or B. Be sure you have at least one Digitrax throttle plugged in ...

The DN163A1 is a board replacement decoder for Atlas N-Scale SD60, SD60M, SD50 and others. 1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the light board inside so that you can install the decoder in the same orientation. 2. Carefully remove the plastic light shroud at the front of the loco and loosen the frame screws enough to allow the removal of the light board. Lift the board out of the frame. 3. Install the decoder, between the frame halves as shown. The narrow part of the decoder fits between the frame with the frame ...

Needs a comprehensive answer.  There may be one somewhere else already.  Z.This is from the decoder manual and does not answer the question:A 12 or 14 Volt lamp run directly without resistors will be less sensitive to voltage fluctuations. For regular 12 to 16 Volt lamps that draw more than 50 mA when lit, we recommend that you put a 22 to 33 ohm 1/4 watt resistor in series with the lamp leads. This will ensure that the lamp "start-up currents" (up to 10 times normal current draw) do not overload the outputs.If you want, you can estimate things by ...

CV # Use Decoder DefaultValue ValueRange CV01 Address All 01-9999 01-127 * CV02 Start Voltage All 001 0-255; higher is more voltage CV04 Acceleration Rate All 000 0 - 31 CV04 Deceleration Rate All 000 0 - 31 CV05 Maximum Voltage Gen4 - 0 (disabled) 1 - 255; lower is slower CV06 Midpoint Voltage All 0 (disabled) 1 - 255 CV07 Manufacturer's Version ID All Variable - CV08 Manufacturer's ID, Decoder Reset All FX3 129 08 to reset,09 reset leave speed tables CV13 DC Functions "On" FX, not on FX3 - See decoder documentation CV15 Decoder Lock FX3 000 See ...

1. Disconnect the wire harness from the LT1.2. Plug one end of the LocoNet cable being tested into the LT1.3. Connect the other end to the cable into on of the LocoNet ports on your DCS50. Make sure the Track Status Indicator Dot is lit.4. All four LEDs on the LT1 will light if the cable is good. LEDs may not all be the same brightness, this is normal. NOTE: Only three LEDs will light if the Track Status Indicator Dot is not lit.5. If any of the LEDs fail to light, recrimp the plugs on the LocoNet cable and ...

Application Note: Con-Cor HO-Scale Zephyr steps needed for the DZ125PS decoder installation Step 1: Carefully remove the body from the frame. There are four clips along each side of the body. (See red arrows) We have found if you start at the rear of the body with a small flathead screwdriver and carefully pry the body outward to remove the back clip, you can move the screwdriver forward to release the others. Once the body is completely removed, carefully lift the light board from its holders on the bulkheads. (See blue arrows) Be very careful as the pins that hold ...

Performing factory decoder reset using Digitrax Zephyr Xtra (DCS51) or Zephyr (DCS50)Overview:To reset a Digitrax decoder to factory defaults the user must set CV08 to a value of 08. It is recommended that this procedure be performed on the dedicated service mode programming track using direct mode programming.Procedure:1. Place the decoder equipped locomotive on an electrically isolated service-mode programming track which is connected to Programming Outputs Prog 'A' & 'B'.2. Press the PROG MODE key until “dir” appears in the LED display.3. Press the STEPS CV key. (The LED display should read “t###” with the # symbols replaced by actual digits)4. Enter “08” using ...

Application Note: Steps needed for installing the DN143IP mobile decoder into the Con-Cor N-Scale Aerotrain "DCC Car". The image above shows the “DCC Car” for the N scale Con-Cor Aerotrain, which is the 1st car behind the loco. It shows the holes in the underbody, above which a speaker can be mounted for a sound decoder installation. The recommended Digitrax sound decoder would be our SFX0416, but to use this decoder the seats will need to be removed. There is a pocket that is 16mm wide, 36mm long and 3mm deep designed for a speaker above the underbelly and under ...

The DH163 series decoders are set up at the factory to control six function outputs. The DH163 is configured to control the forward and reverse lights on the locomotive through the white lead and yellow lead using Function 0 (F0F-forward and F0R-reverse) for directional lighting. Functions F1(Green) and F2 (Violet) are part of the harness for easy hookup. F3 and F4 are also available on the decoder board. These can be accessed by snipping the shrink wrap and peeling it back to expose the solder pads that control these functions: To use these functions, solder a wire from the pad ...

Overview:To reset locomotive electronics to factory defaults the user must set CV08 to a value of 08. It is recommended that this procedure be performed on the dedicated service mode programming track using direct mode programming.* Note: This is the only programming procedure that we recommend using the programming track for. All other programming should be performed on the main track using Operations mode programming.Procedure:1. Place the DCC equipped locomotive on a dedicated service-mode programming track.* Note: The rails of this track should be connected to the PROG A & PROG B outputs on the DCS100 command station.2. Set the ...

1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the shell for reinstallation. 2. Carefully remove the motor springs with tweezers. Store these springs in a safe place for later re-use. 3. Slide the factory light board forward to release it from under the clips on the locomotive frame. Be careful not to distort the frame clips as you slide and lift the light board off the frame. 4. Take the DZ123M0 decoder (noting the correct orientation of the frame pads) and slide underneath frame clips as indicated in the Figure 3. You will need to ...

Braking sections are sections of track which will cause a DCC equipped locomotive to stop automatically. The simplest way to do this is to set up a track section where the power is turned off. This has two disadvantages. First, since there is no power, the locomotive lights will be off when the train is stopped in the section. Second, the lead loco in a consist stops as soon as it hits the dead section. Other locos in the consist will push the dead loco forward. In a long consist, you could get a situation where the last loco in ...

This crane is fully controllable by your Digitrax system. The crane itself turns 360 degrees, the boom raises and lowers, the hook raises and lowers. An electromagnet and searchlight are optional and can also be controlled from your throttle. Only one can be used at a time, but they both come in the same package.Here is a step by step guide to using it with your Digitrax system.The decoder has an address of '08' and is a 28 speed step decoder - selecting the crane requires doing what is known as a "status edit". Hit SEL, turn a knob to ...

1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the light board, so that you can install the new decoder in the same orientation. 2. Carefully remove the factory light board by sliding it toward the back of the locomotive and out from under the frame clips. Then gently lift the board out of the frame. Be careful not to bend the motor contacts. Apply a small piece of Kapton tape to saddle area of the frame above motor. 3. Install the DN163K2 decoder by angeling it slightly as you insert the front corners into the forward ...

DH165K1A Board Replacement Decoder Fits Kato SD40-2, AC4400 1. Carefully remove the locomotive’s shell from the frame. Note the orientation for proper reinstallation (Figure 1). 2. Remove the four track power pickup wires clipped to the lightboard at mid point (Figure 1). 3. Unscrew the two screws securing the lightboard and lift it from the frame. (Figure 2) 4. Remove the lightboard by pulling it gently straight up, off the motor clips. (Figure 3) 5. Decoder installation is the reverse of what we’ve done so far. Snap the decoder into place over the motor clips. Be sure motor clips are ...

I have a Athearn HO Scale MP15 Soo Line and have installed a DH166 decoder. How do I get the rotary beacon to flash? Function Outputs on the DH166 The DH166 is set up at the factory to control six function outputs. The DH163AT is configured to control the forward and reverse lights on the locomotive through the yellow lead and white lead using Function 0 (F0F-forward yellow and F0R-reverse white) for directional lighting. Functions F1(green) and F2 (violet) are part of the harness for easy hookup. F3 and F4 are also available on the decoder board. These can be ...

In order to obtain different brightness levels of lighting, is it permissible to use two lighting function outputs, each with a different value resistors, to the negative lead of the same led or bulb? Yes you may do so. We recommend putting the resistor on the function side vs. the + common side.

The PR4 will only “light up/power ON” when it is connected to a computer via USB.  Simply connecting the PS14 will not power the device and cause any lights to come on. Please follow the complete PR4 installation instructions consisting of PR4 Driver and Software Installation and PR4 Hardware Installation to power and test your PR4. Using the PS14 power supply is only required when using the PR4 for Sound/Decoder programming.

1. Carefully remove the locomotive's shell from the frame (Figure 1, below). Notice the orientation of the shell to the frame so that you can reinstall correctly. 2. To remove the Atlas MP-15DC standard lightboard you will need to loosen the frame screws as shown in figure #1. After the frame halves are loose enough, the standard light board can easily be removed by moving the light board to one side and tilting the lightboard out. 3. Installation of the DN163A3 decoder is the reverse of the removal sequence. With the frames halves still loosened, slide the DCC decoder into ...

CTX/CTY throttles allow you to have up to 4 separate throttles controlled by 4 different operators rather than 4 throttles controlled by one operator as in the CT4 that comes with your Challenger Set. Digitrax provides these instructions so that you can build your own throttles to your own specifications. You are free to choose any knobs, buttons & cases you like, the ones on the parts list below are just suggestions. These throttles give you the option of expanding your operations cost effectively. The CTX throttle controls speed & direction for one train in the operating group & can ...

The Nemo Junction module has a total of seven color light signals that regulate the flow of train traffic through this interlocking plant. Controlling the Signals with SE8C The SE8C is the signal driver, sending current to the various LED's of the color light signals. Each signal is operated via switch commands from the Zephyr. The SE8C has eight Driver Sockets, identified as DRV1 - DRV8. : A Signal Driver Cable (a 10-conductor ribbon cable) is plugged into a SE8C Driver Socket to control as many as four signal heads per Driver Socket. Each signal head can display 4 lighting ...

This Atlas Snap-Track layout appears in the Atlas Model Railroad Company's book "Beginner's Guide to HO Model Railroading". It includes a reversing section which can be controlled with a Digitrax AR1. DC Control For DC operation, Atlas specified an Atlas Controller (for the reverse loop), two Atlas Selectors (to control eight track segments) and seven controllers for the railroad's turnouts. DCC Makes Things Simple With DCC, the wiring of this railroad is considerably simpler. Because each locomotive has a unique address, the section insulated gaps and the two Selectors are not necessary. Likewise, the Controller is replaced with the AR1 ...

Before sending your Digitrax mobile decoder in for repair try these troubleshooting steps to see if you can “bring it back from the dead” and save a trip to the shop and possible repair charge. As with troubleshooting anything, begin checking what could be wrong methodically. Write down your observations as you work through the list to solve the problem.The most common "repair" problem we see in our repair department is decoders that are programmed incorrectly.Many decoders we receive for repair have been programmed with CV values that cause them to seem to have a problem. The good news-bad news ...

This H0-scale railroad track plan first appeared in the Atlas Model Railroad Company's book "Six Railroads You Can Build", written by John Armstrong and illustrated by Tad Stepek. This book was first published in 1958 and has been reprinted several times. A classic bowl of spaghetti, the Transbay Interwoven has two reversing loops and a turntable. DC Control For DC operation, Atlas specified three Atlas Controllers (for the reverse loops and the turntable), two Atlas Selectors (to control eight track segments) and ten controllers for the railroad's turnouts. DCC Makes Things Simple With DCC, the wiring of this railroad is ...

The DN163M0 is set up at the factory to control six functions. The unit is prewired with one golden-white LED (shown in figure below) for the headlight and set up as Function 0 (F0F-forward). Function outputs F0F/Yellow, F1/Green, F2/Violet, F3/Brown and F4/White/Yellow are available on the decoder and can be used by soldering wires from the pads indicated to the lights (or other functions) you wish to control. CAUTION: When adding function wires, be very careful that the wires you add do not come into contact with any other pads or components on the board where they might create a ...

1. Strip the insulation from the red, green, black and yellow wires on the harness. The blue and white wires are not used and may be cut off the harness if you wish.2. Twist the red and yellow wires together. Twist the black and green wires together. 3. To test motor operation, hook up the wires according to the directions in the Digitrax Decoder Manual. One of the two center LEDs will light as the motor voltage increases from the decoder. Change direction and the other LED will light. 4. To test other decoder functions connect the LT-1 to the ...

Most HO, N & Z Scale model locomotive motors and lamps are designed by the locomotive manufacturers to operate at full speed at 12 volts DC on the track. Digitrax recommends running your DCC command station and boosters at the lowest track voltage possible that provides acceptable operation. The “N Scale (12V)” setting on Digitrax equipment works for most HO, N & Z scale layouts. Some DCC systems made by other companies supply more voltage to the track and are not adjustable. If the track voltage applied exceeds the operating parameters of the locomotive and its lamps, it is possible ...

To select and run a DCC equipped locomotive with a known address follow these steps:1. Set the DCS50's Throttle Knob [1] to STOP. 2. Place a DCC equipped locomotive (one with a decoder installed) on your digital layout that is controlled by your DCS50. In this example we assume that you have a new Digitrax decoder that is factory programmed to address 03. If your decoder is using a different address, simply use that address as you follow these instructions.3. Check the DCS50's Track Status Indicator Dot [4] to be sure that track power is turned on. Press the POWER ...

This article courtesy of Ross Webster, which dates from an earlier era before Bachmann made accommodations for DCC installs:There may be others ways do to this conversion, but this is the way I found using the Digitrax DG380 (any DG wired decoder can be used for this installation) DUE TO SOME OF THE FRAGILE ITEMS ON THE SHAY I WORKED ON A FOAM PAD SO THERE WAS NO DAMAGE TO ANY OF THE SMALL PARTS.I first tested the electrical items and made the following determinations.Free running for the two trucks was .8 amps, total. Stall, was 4.6 amps total for both trucks. Smoke ...

I am putting the finishing touches on my 10 x 20 foot H0 railroad. It is a copy of the Cajon Pass, Salt Lake & Santa Fe RR by John Armstrong (#86 in the 101 Track Plans by Linn Westcott) [Kalmbach Publishing, ISBN 0-89024-512-6; still in print]. I have decided to go with DCC and my local hobby store recommended Digitrax. The layout is in my basement, I will be the only operator, the plan has 54 track switches (34 NJ International twin coils and 20 Tortoise turnout motors). Can you give me an idea as to what equipment I ...

  This example is a small yard with a crossing signal at its entrance. We will use independent turnout addresses to demonstrate the flexibility that the DS64 offers. Here, route (track) 2 3 and 4 will activate the blinking light when set and the deactivation is done by resetting to route 1, the main line. The advantage of this setup is that you can easily do operating RR Crossing lights without the need for additional equipment for block detection. The turnout output utilized for the RR crossing operation is simply integrated into the route setup. In addition to the route ...

In earlier generations of model railroading, the reverse loop (reversing section) was the bane of many model railroaders. As the rails of a track come back upon themselves, an electrical short circuit is created. In the analog control world, the solution is to use toggle switches and special wiring to allow the locomotive to move on to the next block. Electromechanical solutions relying on relays and track detectors can also be used to automate reversing on an analog layout. The wye is another example of a reversing section on a layout. One of the advantages of digital command control is ...

The DH165Q1 is set up at the factory to control six function outputs. The DH165Q1 is configured to control the forward-headlight F0F/white lead and reverse-headlight F0R/yellow lead for directional lighting. These two headlight function leads are current regulated for LEDs or lamps, with factory setting of approx 15mA, with no resistors required. Cut the ADJ link to increase headlight current to approx 30mA- see fig 5. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) are full track voltage and can be used by soldering a wire from the pad for the function you wish to use to the ...

The LT1 is a simple decoder tester. Decoder Testing Instructions1. Prepare the cable for use in the testing procedure, by stripping the insulation from the Red, Green, Black, and Yellow wires. The Blue and White wires are not used and can be cut off the harness.2. Twist the RED and YELLOW wires together. Twist the BLACK and GREEN wires together. 3. Hook up decoder as shown in Diagram 2.4. Use your throttle to select the decoder and run it in the forward direction.5. One of the two center LEDs will light as the motor voltage from the decoder increases. Use ...

The DH165K0 is set up at the factory to control six function outputs. The DH165K0 is configured to control the forward-headlight F0F/white lead and reverse-headlight F0R/yellow lead for directional lighting. These two headlight function leads are current regulated for LEDs or lamps, with factory setting of approx 15mA, with no resistors required. Cut the ADJ link to increase headlight current to approx 30mA- see fig 5. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) are full track voltage and can be used by soldering a wire from the pad for the function you wish to use to the ...

You can easily control sound units like the Keller SU1990 by using the function leads on Digitrax Decoders and DCC command station that can control decoder functions. These instructions for connecting a Keller Engineering Diesel Sound unit to Digitrax DH83FX & DH140 series decoders was writtne many years ago.  Any modern Digitrax decoder with 4 function leads can be used. Equipment Needed:1) A Digitrax Throttle, Booster/Command Station or other DCC command station capable of controlling decoder function outputs.2) Any Digitrax decoder with at least 4 function leads will work here.3) The locomotive you wish to convert, be sure to check the ...

The Trix GG-1 is a fine die cast locomotive model which is equipped with a sound decoder. As produced by the Trix factory in Germany, the sound functions are: F0 Normal headlights F1 Bright headlights F2 Cab lights F3 Sound of main relay F4 Low speed switching range (switching acceleration / braking delay off) F5 Bell F6 Horn, continuous blast F7 Sound of pantograph being raised and making contact with the wire F8 Sound of blower motor F9 Sound of switching relays F10 Sound of cab radio F11 Sound of couplers F12 Sound of clickety clack railroad track Digitrax operators ...

 OpSw Setup Enter OpSw mode by pressing the OpSw button.  The OPS and ID light will flash alternating RED and GREEN. Use your throttle in SWITCH mode to set switches to thrown or closed to match your desired OpSw setting.  There are currently no published OpSws for the BXPA1. If you erroneously set an OpSw, the BXPA1 can be factory reset by setting OpSw40 = Closed Trip Speed Pot The Trip Speed Pot can be adjusted to set the speed at which auto reversing and power management is resolved.  Turning the pot clockwise will make the speed slower and turning ...

The DH165A0 is set up at the factory to control six function outputs. The DH165A0 is configured to control the forward-headlight F0F/white lead and reverse-headlight F0R/yellow lead for directional lighting. These two headlight function leads are current regulated for LEDs or lamps, with factory setting of approx 15mA, with no resistors required. Cut the ADJ link to increase headlight current to approx 30mA (see figure below). Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) are full track voltage and can be used by soldering a wire from the pad for the function you wish to use to the ...

This application note is courtesy of Michael K. Perrin, and addresses the installation of an N-Scale decoder in the Bachmann F40PH (now discontinued).  This note calls for using either DN93 or DN140, both of which have been discontinued.  Current decoders such as the DZ125 or DZ143 and other similar N scale decoders can be used.1) Cut a place for the decoder in the back recess in the frame. Because this is a "sandwich" frame there is no room for the decoder without using a saw or Dremel tool to make a cavity for the decoder. (This is the hardest part of the ...

You'll need a few simple tools when you begin installing decoders: A soldering iron, preferably temperature controlled. Though many installations do not require soldering, you may still need to use a soldering iron to install extras like lamps for special lighting effects. Solder. A small screwdriver for disassembling your loco. Small diagonal cutters for cutting & stripping small wire. Tweezers to pick up small loco parts. Heat shrink tubing for protecting wire connections, this is better than electrical tape. 1. Read the instructions FIRST and PLAN your installation. Have the proper tools on hand. 2. Choose a locomotive that runs ...

Good DCC practice means good planning for the electrical needs of the railroad. Here, we talk about the power needs of the Texas & Southwestern. Anticipating Power Consumption The core of the Texas & Southwestern's DCC control system will be the DCS50 Zephyr, which is very appropriate for a small railroad. Zephyr has 10 "slots", memory locations in the command station each holding an active decoder address. Rated at 2.5 Amps, the Zephyr should also be enough to handle the power needs of the railroad, but if more power is needed, then T&SW can easily be expanded with an additional booster ...

Railroad signaling works based on detection of trains on the railroad.  If a train is detected, then the signal system goes into action, setting up indications that let show that the track section is occupied and warn other trains that the section is occupied.  At a grade crossing where a railroad and a highway intersect, the presence of a train starts the crossing signals and lowers the gates in time to stop highway traffic so the train can pass.In the case of real railroads, detection is easy, since the rails are naturally insulated from each other and either a locomotive or ...

1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the shell to the frame so that you can reinstall correctly. 2. The DZ125 has 6” wires that you will solder directly to the appropriate connections inside the locomotive. The smaller size allows the decoder to be easily installed in a variety of locomotives. The bare ends of the wires are wired to the motor connections, power pickup connections and the lights according to this standard. Note: Avoid stressing the solder connections of the wires to the decoder board. If a connection is broken, carefully solder the wire ...

Digitrax SoundFX Decoder Troubleshooting Guide This troubleshooting guide assumes that you are working with an operating Digitrax system that is able to run trains and that the locomotive you are troubleshooting is operational and has a Digitrax sound decoder and speaker installed correctly.  If there is no sound, first make sure the decoder is not muted: Press the Function 8 (F8) key, and make sure F8 is OFF.  Function 8 is used to toggle between sound active (F8 OFF) and mute (F8 ON). If there is no sound and the locomotive won’t move when the address is selected on your ...

Installation: Figure 1 shows the general arrangement for connecting one or more LNRP's to configure a LocoNet based system for operation. Note that the LNRP's drive the power and Railsync signals on the "standard" LocoNet cable segments, so each LNRP should have a DC input of +15V to +18V at up to 250mA supplied on the side DC power jack. Note that the shaded cable connections are made from the protected network side connections of the LNRP units to the components that are on the "protected" or high reliability part of the System. The other solid cable connections are the ...

  I have an "M" shaped 250 square foot layout with 500 feet of track and twelve locomotives. What Digitrax equipment would I need? You don't say what scale this railroad will be modeled in, which is important since the locomotives in smaller scales draw less current than larger decoders. However, for purposes of estimation: Twelve Locomotives. Each locomotive is going to draw, at the very least, 5 MA for the decoder. If it has LED lights, then it will typically draw 15 MA more; conventional light bulbs will draw 50 MA. A typical H0 locomotive will draw 600 MA ...

  The most common problems on the layout that will impact your DCC system are electrical short circuits. If you find that you cannot get the Track Status light on your command station to come up, or there are numerous beeps from the booster, then disconnect one of the Rails from the booster and the problem should be apparent. There is an electrical short in your layout wiring. The quarter test is the BEST diagnostic tool that you have! With your DCC system up and the Track Status ON, create a short circuit across the rails of the layout every ...

The DH165Q1 fits many Atlas, Intermountain, Life-Like & Other factory sound equipped HO locomotives. Installation Instructions - Intermountain F7 example: Removing Locomotive Shell and Disconnecting Lightboard 1. Carefully remove the front coupler and then the locomotive's shell from the frame. Note the orientation for proper reinstallation. 2. Unplug and mark the two track power pickup 2-pin plugs, the motor 2-pin plug and the 6-pin headlight plug(Figure 1) Observe and carefully note the original wire locations! One of the track power plugs and the 2 pin motor plug can be inadvertently swapped when hooking up the new decoder PCB. 3. Unscrew ...

DN163K0b Installation Instructions for Kato F-3, F-71. Carefully remove the locomotive’s shell from the frame. 2. Remove the black plastic cab seat panel by gently pressing in at the sides. 3. Carefully remove the plastic plug that retains the brass motor clips and bend the brass motor clips up and away from the circuit board. 4. Slide the circuit board forward to release it from the clip on the locomotive frame and lift the board off the frame. 5. Remove the brass pickup rail from one side of the locomotive, being careful not to bend it. Wrap a small piece ...

We recommend testing your new SE8C prior to installation on your layout. The following testing procedures will help familiarize you with the general operation of the SE8C. Track power needs to be ON, a working LocoNet connection and a throttle or PC running DCC control software. Pre-Installation Set-Up 1. Solder one wire from a 12V AC or 15V DC power supply to Pin 3 and the second wire from the power supply to the Pin C on the 44-Pin edge connector; this powers the SE8C. Digitrax manufactures the PS14, which is appropriate for this installation. Multiple SE8Cs can be powered ...

Model railroad layout signaling is just as complicated as real railroad signaling. This is an example of how signaling might work on a small oval layout.  Once you understand how the signals work together in a simple setting, you will be better equipped to tackle signaling on your layout. The layout is a simple oval with a passing siding. Here are the locations of the individual signals: This railroad has four Absolute signals, two Dwarf signals and two Permissive signals.The four Absolute signals and two Dwarf signals protect not only the main line & the passing track but also the two turnouts ...

1. Carefully remove the locomotive's shell from the frame. Notice the orientation of the circuit board inside so that you can install the decoder in the same orientation. (Figure 1) 2. Remove the 10 black plastic plugs from the lightboard that secure the wires to the PCB. There are 4 plugs (retainers) on each end and 2 on the side for the motor connection. Remove the red and black wires, carefully noting where each wire originally connected to the PCB. Remove the lightboard itself by pinching the black plastic release tabs and pulling the board up and off of the ...

Q:  Is it possible to use Digitrax equipment to wire the Kato N-Scale Automatic Track Crossing? If so, how do I do it? A:  The answer is a probable "No", but there may be a workaround. The Kato, USA website notes: Some Unitrack components such as the Automatic Crossing Gate and 3-Color Signal were designed with DC operation only. So, the official position is that that these devices don't work in the DCC environment. However, we are not above speculating on how to do this, nor are others. An online web search turned up this bit of message traffic by ...

The Kelana Jaya Rail Line model is a DCC intense layout, using many Digitrax command control components to achieve the goal of training operators of the actual rail line. The railroad was built in the 1990's and many of the Digitrax devices used for the Kelana Jaya Rail Line model have been superseded with improved units. Components used for the Kelana Jaya layout: 28 Mainline turnouts 11 Yard turnouts 39 Tortoise switch machines 84 Dwarf signals (yellow/green, red/green, red/yellow) 38 Mainline block signals 38 Heavy duty SPDT switch relays Digitrax Components Used for the Kelana Jaya layout: 1 DCS 100 ...

1. Read the instructions FIRST and PLAN your installation. Have the proper tools on hand. 2. Choose a locomotive that runs well on regular DC. 3. Choose the appropriate decoder for your installation. 4. Test the decoder before installation. 5. Carefully disassemble the loco. 6. Isolate the motor! 7. Follow the decoder's wiring diagram or installation instructions. 8. Test the installation first on DC then on DCC. (If the lights are flashing the first time you apply power, remove the loco from the track and locate the short circuit in your installation.) 9. Customize your decoder by programming individual CVs.

All current Digitrax mobile decoders have FX3: all function outputs incorporate FX generators for prototypical lighting effects full function re-mapping so you can choose which function (F0-F12) controls each function lead

  Q:  On my PR2, I have been getting the red light and message saying COM Port Paused a lot when trying to read CV’s. A:  This operation is normal. Whenever you bring up any of the auxiliary menus such as Soundtest or CV editing, the main Soundloader screen pauses its communication with the PR2 so the auxiliary menu operation can take place. When in the normal main screen, the program is constantly talking to the PR2 so it must be paused to allow these other activities to take place. Unless you are not able to read/write CV's, this should ...

Function-only decoders allow you to add additional functions to a locomotive with an existing mobile decoder.  Additionally, function-only decoders allow you to install lighting in passenger cars, as an example.Function only decoders also are used to add Digitrax transponding to early model Digitrax decoders and decoders from other manufacturers that do not have this feature.

DG583S - Function Outputs 1. Function outputs are rated at 2 Amps each. Do not exceed the decoder’s 5 Amp total output rating. This total includes the motor current and total of all function output currents.2. To use a function output with an inductive(coil) type load, see the Digitrax Decoder Manual for more information to avoid damage to the decoder.3. See the Digitrax Decoder Manual for full details of wiring 12-16V lamps, 1.5V lamps, and LEDs. Lamps that draw more than 80 mA when running require a 22 ohm 1/4 watt resistor in series with the directional light function lead ...

UT4 Sleep Mode is used to extend throttle battery life; it does not charge the throttle batteries but it does reduce the draw on the throttles' batteries.To put the UT4 to sleep, press and hold any function key down and turn any address selector to the next digit. The throttle will go into sleep mode. The UT4 will release the address that was selected and the status light will briefly turn red. If the unit is plugged into LocoNet port you can unplug the throttle and the throttle will then be in sleep mode until plugged back in to LocoNet ...

QUICK INSTALLATION Notes for users with decoders not made by Digitrax:1. The DCS50 command station operates in 128 speed step mode. If you are using a locomotive with a decoder that does not have 128 step capability you will have to adjust either the decoder or the DCS50 so that both are using the same number of speed steps to communicate. We call this procedure status editing. You can status edit each individual decoder or you can change the DCS50’s system default by setting the DCS50’s Option Switches 21-23 and run all of your decoders with fewer speed steps to ...

The RD2 allows Remote Sensing of 2 Detection sections.  It eliminates the need for long runs of Heavy gauge wire to the BDL168. 1. Mount the RD2 as close to the detection section as possible to keep heavy wire to a minimum. 2. Make sure both detections sections of the RD2 are connected to the same zone of the BDL168. 3. Light gauge (26AWG) wire can be used for the 3 output connections running from the RD2 back to the BDL168. The RD2 can be located up to 200' away from the BDL168. 4. Heavy gauge (18AWG) wire should be ...

Dispatching is a special way of offering a locomotive address to a UT1 or UT2 to run. The address is set up and then dispatched to the system to be acquired by the next throttle that presses its ACQUIRE Key. This is not the same as releasing a locomotive address from the system. Releasing an address clears it from the locomotive slot to make room for another locomotive address to be run by the command station. 1. Set the address selector switches to address “99” then press the “ACQ” button. 2. The Status LED will light green showing that you ...

"Turnout" is a civil engineering term for what railroaders call a "switch".  In the model railroad environment, we often use the word turnout to avoid confusion with the electrical term "switch".  On the railroad, throwing a switch usually only means one thing, while "Throw the switch" on a model railroad could mean operating a light switch.Probably the best answer is to consistently use one type of turnout.  The notion of a "DCC Friendly" turnout is a myth; the standard answer in the past has been: "If it worked on DC it will work on DCC". In the end, which turnout ...

MU OPERATION Place the two units you wish to MU on the tracks controlled by the command station 1. Select the lead locomotive on the right side throttle  2. Select the engine to be added on the left side throttle 3. Make sure all the locomotives in the consist are traveling in the same physical direction. The direction lights may or may not be the same (green or red) depending on the orientation of the locomotives in the consist (head to head or tail to tail). 4. Push "mode" Button 2 times 5. The display should now show both locomotive numbers. 6. ...

The UT4 series, UT4, UT4D & UT4R are "traditional" style throttles.  The UT4s were developed from a specification submitted by Digitras users through the Digitrax Yahoo group. These throttles were designed by operators for operators.  They are also great for beginners because of their intuitive controls and reduced feature set. By not offering all the bells and whistles, beginners can run your railroad without accidentally changing settings that might cause problems.   Works with any LocoNet compatible system   4-Digit addressing   Functions F0 - F12 for lighting and sound decoder operation   Direction switch with center brake position   ...

A TF4 can be used with any decoder that is not transponder equipped to add transponding capability to the loco.  It can also be used in any piece of rolling stock with track pick ups to add transponding.  For example, you could use a TF4 to add transponding and lighting effects to a caboose if it is equipped with track pickups to provide power and signal to the TF4.A TF4 should not be connected to an existing transponder equipped DCC decoder unless the DCC decoder's transponder is disabled. This avoids having 2 transponders responding to the same address in the ...

I am installing a DH165A0 in an Athearn SD70. The head light outputs are a nominal 30 ma (with the link cut). The bulbs were of course a bit lower in their current demands and were very bright for a short while. Is there any way to lower the current output from 30ma or do I need to add a resistor in line with the bulb to drop the voltage output? Of course if it is supposed to be a regulated current output this might be a problem. The DH165A0 has a constant current source for F0F and F0R, so ...

Prior to Disassembly Test the Decoder All Digitrax decoders are tested for proper operation before they leave the factory, but sometimes strange things happen. Therefore to insure your decoder is covered under our warranty policy, please give it a thorough test BEFORE you cut the wires. Test Run the Locomotive Be sure it runs correctly in both directions with no unusual noises or binding in the motor-gear train. If it checks out OK, then: Get Ready Before you start, get your tools and supplies together for this project. You will need the following items: DECODER TESTER - Such as the ...

Q:  Can I add a booster to my Zephyr? A:  Yes. Since the DCS51 Zephyr Xtra and DCS50 Zephyr are equipped with LocoNet, adding additional boosters is easy; you simply divide your railroad up into power districts and add the boosters and their individual power supplies. These are connected together using LocoNet cables. Because the Zephyr Xtra is rated at 3 amps and the Zephyr is rated at 2.5 amps: most boosters have higher ratings, you may want to have the Zephyr control a smaller area that has fewer power consumers (locomotives, lighted passenger cars), such as a main line ...

It is important to realize that the standard only covers the communication protocol on the track.  As long as it is not extended further than the basic track level communications for train control, creativity will be encouraged rather than stifled. This protocol is very basic and does not require any particular hardware. The Digitrax Complete Train Control System incorporates the DCC protocols for interoperability reasons but has not been held back by them.  Digitrax has developed and marketed automatic reversing boosters, decoders with 128 speed steps and user customizable speed tables, mobile decoders with onboard functions and lighting effects, stationary decoders with sophisticated ...

I have an old Diamond Scale turntable; this turntable uses a rotary switch to select which stall or track you want to align the table with. It is basically a closed connection, or relay connection to select the track you want. I was wondering if it was possible to use the DS64 to create a closed connection (relay output) to activate this connection for the turntable position. Basically I want a relay output from the DS64 to be addressed by my DT400. Using throttle control This should be fairly easy, but not in the way that you envision it. The ...

There was an error In the BDL168 Instruction Sheet, Figure 6 on Page 19.  The LT5 diagram was incorrect.  This article shows the correct LT5 Detection Sections.  The current on-line version of the BDL168 Instruction Sheet has been corrected. Each BDL168 comes with an LT5 that will help you with layout wiring and troubleshooting for transponding & detection. The LT5 plugs onto the LED header connections of BDL168 and the LEDs on the LT5 light when detection sections are occupied. The status of power to each zone is also shown. In service, the LT5 is plugged in to one of ...

Installation Notes: 1. Do not exceed the decoder’s 500mA total function output rating. 2. We recommend that the Blue wire, also called +Common or Lamp Common, be connected as shown. If you wish to omit the Blue wire in your installation, consult the Digitrax Decoder Manual for more information. 3. The head lamp should be hooked up using the Blue/+Common wire for optimal Digitrax transponding operation. 4. To use a function output with an inductive (coil) type load, see the Digitrax Decoder Manual for more information to avoid damage to the decoder. 5. See the Digitrax Decoder Manual for full ...

If the function you want to operate does not respond, check the following:1. Is Track Status [4] on? If not press the POWER key to turn it on. 2. Did you select the correct loco? If not, select it now.3. Is the function you want to use installed in the loco? If not, you may need to install it. Most new locos have a head lamp/backup lamp installed, but most do not have any additional lights or sounds installed.4. Change the position of the Direction Control Lever and see if the lamp comes on in the other direction. If the ...

Differences in the DS74 from the DS64: Up to date and compact LocoNet design with customer IPL/firmware field update capability using DigiIPLII. All plug-in connections. Can support on expansion header up to 4 DSXCP1 fascia SW control panels with SW direction indicator LEDs. 8 internal LocoNet integrated System routes, that can be conveniently edited on a DT602 with latest IPL update. Configurable unit Base switch address when on layout. No need to remove from layout to service/configure. Automatic DS74 switch address overlap detection, and correction capability when editing with DT602. Indicates internal IPL Sub-version loaded to latest DigiIPLII rev 2.9 ...

  There are two methods of providing power to the DS54: from the rails and from an auxiliary power source. The DS54 can be powered from the rails however, Digitrax strongly recommens that the DS54 be powered from an auxiliary power supply capable of delivering 12-16 volts (ac or dc) at 300 millamperes for best results.  Powering the DS54 from the rails reduces the current available to power locomotives and lighted rolling stock.  The auxiliary power supply connections are the red (+) and black (-) wires. Note: Digitrax recommends the PS14 Power Supply for independently powered DS54’s. Multiple DS54’s can be powered from a single power ...

1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the shell to the frame so that you can reinstall correctly. 2. Remove the 6 pin analog shorting plug and in its place insert the DZ125IN/DZ126IN decoder with the correct pin-1 orientation. (There also is a small numeral "1" on the bottom of the DZ125IN near pin-1.) The DZ125IN has 6 pins that insert directly into the 6 pin socket (NEM 651 type) on the locomotive’s PCB. The DZ125’s small size allows the decoder to be easily installed in a variety of European locomotives. For the Kato ...

I would like to use a Tomar Searchlight Signal such as model # 858. It has three color LED for each head. The SE8C manual shows the wiring example for bi-color LED signals. Is the SE8C able to control the three color LED signals as well? The bi-pole LED's can be used to produce a yellow "Approach" indication. The SE8C sends an AC signal to the LED, alternately lighting both the red and green sides to make a yellow (or "amber") Indication. Please see below: "A2" is connected to produce an approach (yellow) indication. You may find that the yellow ...

DS64 Quad Stationary Decoder      The DS64 is a Stationary Decoder for use with 4 slow motion, solenoid, or bi-polar turnout machines Simple to hook up and configure   Controls 4 individual turnout machines: EITHER4 Slow motion turnout machines, such as TortoiseTM by Circuitron or SwitchmasterTMOR4 Solenoid-type turnout machines such as three wire (twin coil type) Peco or Atlas Snap Switches or two wire bi-polar type turnout machines such as Kato Unitrack, AristoCraft, or LGB turnouts with capacitive discharge capability  Support for up to 8 routes   Screw terminals make installation easy   Use with any LocoNet Compatible System   ...

Consisting is the action of linking more than one locomotive or power unit together to be controlled by a single locomotive address.  The UT4 is not capable of building or breaking up a consist.  This is handled by a throttle or computer program that is able to build and break up consists and then hand the consist off to the utility throttle operator.  Utility throttles are designed to be simple to use for operators on the railroad.  The UT4 CAN control a consist by selecting the address of the TOP loco in the consist.  It can also control the functions of locomotives within a consist.If ...

How does DCC work? You use a throttle (cab) to tell the system what you want a train to do. The throttle sends the information to the command station. The command station makes a digital packet out of the information and sends it to the booster. The booster* adds power to the digital packet and sends it out through the rail. The decoders in all locomotives (even those that are not running) read all digital packets, and decipher them to get the address contained in the data packet. If the packet address matches the decoder address, the decoder uses the ...

The PM74 OPSW41= C will change the 4 DS1-4 led display, so each DS led now reports the same way the PM42 leds did. This is a Legacy option provided for users who want the PM74 indications to be similar to the PM42. The default OPSW41 =T has the DS led light ON for resistance Occupancy detection within that DS, and will flash when a Transponder is present in that DS. These 2 additional DS detection capabilities and indication were NOT present in the PM42. Whatever the OPSW41 state is, LocoNet messages will report Power state/action,  Occupancy and Transponding messages to a connected LocoNet, ...

Testing the installed TF4 for correct transponder operation1. Place the unit with the installed TF4 on an empty transponding track section. This test assumes that the transponding track section is already set up, tested and is working before you start TF4 testing.2. Using a DCC throttle, select the TF4 address that was programmed into the TF4 and verify that the transponder detector identifies the presence of the transponder device. Depending on how you have set up your transponding reporting to the system, your system should detect the presence of the address in that transponding section.For example, if you have an ...

Installation Notes: 1. Do not exceed the decoder’s 500mA total function output rating. 2. If you plan to use functions F1 (traditionally a green wire) or F2 (traditionally violet), the return, also called +Common or Lamp Common, should be made via a wire carefully soldered to the Common (or blue) pin indicated as shown in Figure1. 3. To use a function output with an inductive (coil) type load, you must install a kick-back suppression diode across the connections. If controlling a coil type load, such as an electromechanical relay or motor, shutting the device off can cause an inductive kick-back ...

The Track Power indicator on your DT402 display shows the track power status. There is also a Track Status light on your Command Station. If the track power indicator is lit then track power is on. To turn the track power on or off: 1. Press the PWR key on the DT402. You will see a screen similar to the one below. You will now be able to toggle the track power on/off: 2. Press the N/- key to toggle the track power off. The Track Power Indicator on your DT402 and on your Command Station will go off. 3. ...

To run two or more locomotives together as a multiple unit lash up or consist controlled by a single locomotive address: Place the two or more units you wish to MU on the track. 1. Select the TOP loco (the one that will control the consist) on the right hand throttle knob. 2. Select the loco to be added to the MU on the left hand throttle knob. 3. Make sure all the locos in the consist are traveling in the same physical direction on the track (both going to the left or to the right) 4. Press the "MU" key 5. Press the "+" key 6. ...

Most modern command stations and decoders are set up to run 28/128 speed steps.  If you are using older command stations or decoders you may need to adjust one or the other to get the trains to run.Why are more speed steps better?The reason you want to use a command station and decoders with 128 speed steps is for smoother speed control of your locomotives.   Digital command control signals are just that, digital.  When you send speed commands with your throttle, you are sending digital instructions telling the decoder to change from the current speed to a different speed.  When ...

The UT4 comes InfraReady for layouts that are equipped with one or more UR90 infrared receivers. For Infrared operation:1. Install one or more UR90 infrared receivers on your layout.  These should be connected to LocoNet and powered.  If you have UR92s and/or UR91s present on the layout, these also support infrared operation.  You will need enough infrared receivers installed on the layout so that the throttles you use can "see" the receivers since the transmission is line of sight.  You may also encounter problems in rooms where there are large windows that would interfere with the transmission.2. Install a 9 ...

Photo Courtesy Kato, USA Installation Instructions: The DN143K2 cannot be tested prior to installation in the rail diesel car. 1. Carefully remove the shell from the RDC. Carefully remove the plastic casting from the bottom side of the RDC frame, using a flat bladed screwdriver to pry it loose. 2. Gently remove the white clip that holds the seat panel in place. Remove the seat panel by pushing up gently from the bottom of the frame. The seat panel has clips underneath that are very easy to break, so be careful. 3. Take extra care to notice how the RDC ...

Needs to be investigated  Z.I am looking at buying one of your Super Chief systems. My question is :- Do you have to carry a bus under the boards or could you use an adhesive copper tape on the top of the board .  My system will be totally new; layout size 10 foot 6 inches x 8 foot.  Model Rail DVD showed this.The core power bus of the railroad is an important component.  Remember, the Super Chief will be delivering either 5 Amps or 8 Amps of electrical power.  Your interest is to make sure that sufficient power readily ...

LocoNet System ArchitectureDigitrax LocoNet is a Peer to Peer local area network (LAN) designed specifically for model railroad operation.  System architecture is the biggest difference among DCC systems, the way the components of a DCC system communicate among themselves. LocoNet wiring is cost effective, flexible and expandable to accommodate almost anything you want to do with your railroad today and in the future.System ExpansionHere are some of the expansion possibilities available with LocoNet. With Digitrax LocoNet your DCC journey starts at the Main Station with your first “starter” set. From there, it’s up to you. You can add:  Mobile decoders ...

  CV29 is assigned a single value which chooses a combination of specific effects: 1. Speed step control. 2. Speed table On or Off. 3. Analog mode conversion On or Off. 4. Normal Direction of Travel (NDOT). 5. 2 digit addressing or 4 digit addressing. Analog Mode Analog mode conversion is very convenient if you plan to run your Digitrax decoded locomotive on regular DC layouts. With analog mode conversion enabled, the decoder will automatically begin operating as a DC locomotive when no DCC signal is detected by the decoder. This means that if you place your Digitrax decoder equipped ...

1. The UP5 Universal Panel is designed for mounting on the fascia board of the layout. Cut a hole approximately 2.5” W x 1.5” H in the fascia board. Insert the UP5 through the hole with the face plate on the front of the fascia board. Attach the UP5 face plate to the fascia board with four #6 screws. Note: The UP5 uses the black screws to mount the front fascia plate.2. Connect the UP5 to LocoNet using pre-tested LocoNet cables. There are 2 LocoNet Jacks located at the back of the UP5 board for connecting LocoNet devices on your layout. ...

Resetting Factory Defaults You are unlikely to encounter a problem that will require a factory reset. One such instance may occur if you set a password for your Duplex Group name and forget what it is. Resetting to factory default condition is an easy way to correct the situation. Note: If you have more than one UR92 in your layout, you will want to disconnect all of them to do a full factory reset on each unit as follows. Once they have been reset, reconnected to your LocoNet, and allowed to renegotiate a common Group name; you can change the ...

Photo Courtesy Kato, USA The DN143K2 replaced the earlier DN122K2 as a custom decoder designed for the Kato RDC in N-Scale. This is not a particularly easy installation and there have been some reports of problems with the headlights. Paul Lator has some experience with this installation, and this may be of help to you: "The wiring with the DN143K2 works well if you do not route the wires over the top of the seating in the RDC, rather completely disassemble the unit, mount the decoder in it's designated location then run the wires through the drive shaft tunnels. Place ...

If you have more than four turnouts, you will need to program the addresses.The DS64 has 4 Output pairs labeled 1R & 1G, 2R & 2G, 3R & 3G, and 4R & 4G.  The DS64 is shipped from the factory with these outputs programmed as Switch Addresses 01, 02, 03, and 04 respectively. You can set the Switch Address of each of these four Outputs to any value from 01 - 2048.NOTE:  During this procedure the DS64 must be connected to an active LocoNet with an active command station.1. On the DS64’s control panel, press and hold the ID button ...

When you are finished with your session, you should shut down the DCS50 by turning off power to the system.Shutting Down DCS50 Zephyr1. Bring all locomotives on the layout to a stop by setting set the Throttle Knob for each loco to STOP. 2. Turn track power off: Press the POWER key, the DCS50's Track Status Indicator Dot will go off. The display will briefly display "Po" followed by two characters, the Po means power off, the two characters indicate which software version is installed in the unit. The display will automatically revert to showing the last loco address selected ...

In response to questions about the differences among the DCC systems that are currently available from different companies, I offer the following comments & observations. You may have heard that all the systems are pretty much the same or you may have seen “comparison” charts in various DCC companies’ literature, in magazines or “analysis” on the Internet by “impartial observers.” Unfortunately, it is almost impossible to break down the system and company differences on a simple chart & the people who write the “impartial analysis” are usually not really impartial. As you read these comments, please keep in mind that ...

The Texas & Southwestern has a reversing loop, and DCC insures reliable and simple operation of trains in the reverse loop. This reverse loop is handled with a Digitrax AR1 Auto Reversing Controller. The automated features of the AR-1 make for seamless train movements, but an issue quickly arose. Because a reverse loop in a traditional DC-powered model railroad environment required manual operation, the track insulating gaps for the loop were usually located for the convenience of the operators. So the track gaps of the original track plan were situated to keep this inconvenience to a minimum. Note also all ...

Decoder Installation instructions?? is this included in the PDF for this decoder or is it a stand alone decoder installation app note?  Z.1. Carefully remove the locomotive’s shell from the frame. 2. Carefully remove the plastic plug that retains the brass motor clips and bend the brass motor clips up and away from the circuit board. 3. Slide the circuit board forward to release it from the clip on the locomotive frame and lift the board off the frame. 4. Gently lift up (about 3 or 4 mm) the brass pickup rail from one side of the locomotive, being careful ...

What Digitrax decoders work in the new Athearn N scale FP45? We recommend the DN163K1C, following the procedure below. One of our editors was able to successfully install both the Digitrax DN163K1B and DN163K1C decoders in the unit. We have determined that the chassis design requires that the decoder be installed backwards. The only problem this poses is that one additional step has to be taken when programming. Both the DN163K1B and DN163K1C decoders are the same footprint with the exception of the LEDs. The DN163K1B has T-1 3mm LEDs and DN163K1C has surface mount LEDs. When the K1B version ...

Setting up your new Zephyr: Unpack the DCS-50 command station and the PS-315 power supply. On the back of the DCS-50,locate the gray screw terminal strip.On this strip, locate the two terminals labeled “RAIL A “and “RAIL B”.Attach these terminals to your track wires.It does not matter which is which. Before proceeding to the next step,make sure the throttle knob [1] is turned all the way to “stop” and the direction/brake lever [2] is set to”brake”. [See photo blelow]. Now, find the plug on the back of the DCS-50 marked “POWER IN, 15 VAC, 2.5 AMPS”. This is where you ...

I have an older Rivarossi Heisler that I have just installed a decoder in. I have 2 other Rivarossi engines, older, with decoders in them and they work. I use them as a template. Anyway, I can't get the Heisler to run. I have the orange wire at one side of the motor and the gray at the other. The red is soldered to the frame and the black is connected to the front screw where I disconnected the light etc. I just soldered the wires together. The motor is OUT of the frame so no short can happen. Can you ...

I have a Broadway Limited Import diesel locomotive equipped with factory DCC and Sound. Every time I turn on my Digitrax Zephyr DCS50 the engine starts to short out. It begins to slow down and then jerks a little and sometimes it stops completely. My Zephyr shows a line of flickering zeros across the dial and the engine decoder number even flickers on and off at times. I have checked all terminal connections and for foreign matter on the track but have not had any success in solving the problem.I have taken all cars off the track to make sure ...

Note: These instructions cover the hardwired installation of any Digitrax decoder with wires into a Kato GP35 H0 Diesel. Currently, the recommended decoder for current production GP35's from Kato are the DH163K0 board replacement decoder.  Using the board replacement decoders are much simpler and cleaner installation than the one described here.Tools Needed for Decoder InstallationYou'll need a few simple tools:1. A soldering iron, preferably temperature controlled.2. Solder3. Screwdriver4. Small diagonal cutters for cutting and stripping small wire5. TweezersMotor Isolation for Kato GP35Carefully remove the loco's shell and weight.To isolate the motor, disconnect the brass strips (motor brushes) from the track pick up ...

The DT400 can control Functions 1 - 12.Note: DT400 can access F0-F12 when used with the DCS50 Zephyr or DCS100 Super Chief command station. DT400 can only access F0-F8 when used with a DB150 Super Empire Builder command station.To enter Fn (function) mode:1. Determine which throttle you want to control functions on and make it the active throttle by single clicking the throttle knob or by turning the throttle knob a couple of clicks.2. DT400’s numeric keypad is always active in function mode during normal loco operations. When the mode indicator on your DT400 shows Fn, simply press any number ...

LocoNet is Digitrax's method of communication between LocoNet compatible devices on a model railroad layout.  LocoNet compatible devices are designed to work together on the network, and in some cases can also accept DCC commands from  the track, but often go beyond the scope of simple DCC train control.   LocoNet is a peer-to-peer Ethernet type multiple access network.  Because of its design architecture, it is very robust and powerful.  Layout implementation is simple and wiring is free form with minimal limits. LocoNet is designed to run an unshielded 6 conductor ribbon cable.  Digitrax recommends using flat, six-conductor telephone wire ...

There is a numeric keypad on the DT402/DT400 throttle.  The numeric keys on the keypad are primarily related to the throttle mode shown in the LCD’s mode indicator area, but can be used for numeric entry and function control in other modes. For example, when the command station is in the Function Mode Fn, the numeric keys are used for function control. When the command station is in the Locomotive Mode,Lo, the numeric keys are used to enter loco addresses. When the command station is in the Switch Mode is Sw, the numeric keys are used to enter switch addresses.In ...

When the PR3 is powered up and properly operating, the green ‘USB’ light on the PR3’s control panel will be blinking steadily and the red ‘STAT’ will be blinking momentarily. Make sure the supplied SoundLoader Installation CD is inserted in your PC's CD player. Plug the PR3’s USB cable into a vacant USB socket on your PC . Depending on which operating system you have on your PC, you will next see a dialog box appear on your PC’s monitor. The procedure we document in the following pages is for Windows XP, if you have Windows Vista®, Windows 2000®, or ...

When the BDL168 is connected to LocoNet, it will communicate coded detection information to the system. If you wish to report BDL168 status to LocoNet and attached devices or computers that can interpret these messages, you will probably want to set up a unique board address for each BDL168. This is done so that the BDL168 Board ID does not conflict with the Board ID of other devices on the railroad. Board addresses can range from 01 to 999. It is recommended that you make a record of the addresses you use for all devices connected to your layout. Setting ...

The term smooth DC is used to describe the power provided to the layout by conventional model railroad power packs (analog transformers). Traditional model railroad power packs convert household line current into 12-18 volt current to power your model railroad. Voltage is supplied to the track, and as the voltage increases, the speed of the locomotive's motor increases, which makes it run down the tracks at faster speeds. Some power packs put out only AC (alternating current), while others put out DC (direct current) and AC (for accessories such as track switches and building lights). AC powered trains tend to ...

I want to run a small 12V -16V AC motor via DCC and am not sure if you have a decoder for this and if so how to connect up.For Variable Speed:Some Digitrax decoders, such as the DG583S, can be programmed to operate AC motors. When you program CV61 to a value of 004, Digitrax decoders with split field motor drive capabilities will convert their motor leads to drive a "split field" AC motor instead of the default DC motor. This lets you run Maerklin 3-pole AC motors and similar motors in a number of locos built in Europe with ...

The prototype operation that gains the most from DCC is one of those least frequently modeled today: Rapid transit. Rapid transit consists of streetcars, interurban, subway, elevated or commuter rail track and equipment. The trains are usually very short and intervals between trains are relatively brief. Lots of trains run each hour and many trains are running at the same time. All of this operation is very much like a typical model railroad. Any photograph of a major downtown in the streetcar era will have from two to ten streetcars visible with some only feet apart. Simulating this type of ...

Digitrax series7 mobile decoders have many industry standard Configuration Variable (CV) numbers and values, as well as numerous Digitrax custom CV numbers and definitions or controls. The series7 CV values are a superset of older Digitrax FX3 series3 and series6 decoders, already covered in Digitrax Decoder Manual V2 on the Digitrax Web site. The “CV8 to 8 default” columns indicate current factory defined value after writing a value of 8 to CV8, using; Service mode programming track or Mainline Operations Mode Write to the active decoder address. An entry with value/xx indicates a xx number invokes the value before the ...

LNWI Security Considerations: Enabling and Customizing WPA2 Security The LNWI has the option of enabling WPA2 security to require a passcode to connect to the LNWI SSID.  The primary purpose of this passcode is to limit access to the LNWI in a public setting.  This is designed to operate in a similar function to the passcode options for Digitrax Duplex Radio. Using an unsecured connection poses minimal threat to LocoNet access as the LNWI only utilizes a limited number of LocoNet commands.  The LNWI does not have access to programming capabilities or other advanced LocoNet capabilities on your layout.  No ...

BD4 Output Each BD4 is situated between the PM42 Power Manager and the railroad. The DCC signal passes from the DCS50 Zephyr, through the Power Manager, through the BD4 to the track to the locomotive. When a locomotive (or equipped car) is present in a track segment, the BD4 also sends out occupancy information, in two ways. Occupancy Information Output LED1 The LED1 10-pin header is for testing the status of power to the rails and block occupancy with the LED indicator which is included with the BD4. The LED1 can also be used for panel indicator lights using LED's. ...

Direct Home Layout Wiring Digitrax strongly recommends direct home wiring where each power district and its booster are electrically isolated. This method of wiring has safety advantages and makes troubleshooting problems easier. In addition, direct home wiring makes detection work more prototypically. With direct home wiring, the BDL168 can determine and indicate whether any of its 4 zones is powered or not (possibly short-circuited) even when there is nothing on the rails in the detection sections. The BDL168 factory-set logic causes the detection sections to show "occupied" if the associated zone's power is off (because in this case, detection is ...

These instructions will get you up and running quickly. A full description of all controls and technical reference information are included later in this section of the Tech Support Depot. This section assumes that you are using a new set straight out of the box. If your set is radio equipped, we recommend that you follow this quick start guide without using radio to learn the basics. When you are successfully running your radio throttle tethered to the system, then go to the DT400 series tetherless overview article to learn how to install the radio option. Connect the DB150 to the ...

DCS50 Zephyr - Quick Start Guide 1. Unpacking Your ZephyrUnpack your box and locate the DCS50 Command Station and the PS315 power supply. 2. Before You BeginBefore proceeding to the next step, make sure the Throttle Knob is turned all the way to “STOP” and the Direction/ Brake lever is set to “BRAKE”. 3. Connecting the Pieces TogetherOn the back of the DCS50, locate the gray screw terminal strip. On this strip, locate the two terminals labeled “RAIL A” and “RAIL B”. Attach your layout track wires to these terminals. It does not matter which is which. 4. Turn on ...

This article stops in a strange place??  We need to find the rest of it and split it up into meaningful chunks.  Also needs meta stuff Troubleshooting in General:Regardless of the guides, manuals, tips, suggestions, experts or whatever, troubleshooting can occasionally degenerate into a vast chasm of darkness and confusion.  It would be impossible to cover all the areas that have, can or may cause problems. This is a general guide to identifying and resolving problems with Digitrax Complete Train Control.  Keep Good Records:Although it may seem to be a pain while setting up your Digitrax system, keeping layout records ...

Decoder Lock lets you use more than one decoder in a locomotive and be able to program their CVs separately.  This is a manufacturer specific CV.  The instructions provided here work for Digitrax decoders.  If you are using decoders from another manufacturer, please consult your decoder instructions for how this feature works with the decoder you have installed. For example, if you use a mobile decoder and a sound decoder together in your locomotive, you can use the same mobile decoder address during operation and when programming you can unlock only the one you want to program. Since all decoders with the ...

I am now constructing an N-Scale layout with Digitrax DCC system. I know SE8C and two-heads signal mast supplied by your company are applicable for a entry signal mast for the both of main and siding (branch) lines. However, I don't know how the signal mast is used in the case of "more than two" siding lines. For example, the next picture was taken in Powder River Basin (Converse Jct.) in Wyoming State. TS, Japan In this picture, some two-heads signal (mast) can be seen. In every signal mast, the top signal head will be for a main line. But, ...

The DT402 Throttle will control up to 29 functions in walkaround and radio modes. When operating in IR Mode the DT402 series throttles will control up to 9 functions (F0-F8). The numeric keypad is always active in the normal Fn operation mode. The functions that are currently on for the active loco will be displayed on the top line of the DT402 display. The following figure shows an example of how the display looks when functions 0 and 1 are turned on for loco 1652 on the R Throttle. Controlling Functions F0-F12 1. Determine which throttle you want to control ...

The DB200+ is the 8 amp booster. It has NO command station capability. This booster was designed for adding power to layouts that run lots of locos and for large-scale layouts where power requirements are heavy.DB200+ Control PanelNOTE: DB200+ front panel graphics may vary from those shown here.  Internally the booster is the same. These instructions are written for both versions of graphics as well as the DB200+ OPTO optoisolated version of the booster. About the Green Jumper WireEvery DB200+ is shipped with a green jumper wire on the front panel Booster Terminal Plug connecting Synch & Ground or ‘Config ...

Preparation 1. Carefully remove the locomotive's shell from the frame. Note the orientation for proper reinstallation. (Figure 1) 2. Remove the four track power pickup wires clipped to the lightboard (2 on each side) (Figure 2) Carefully pull the brass motor clips from under the track power "staples" on the lightboard. 3. Unscrew the lightboard screws to release PCB from the frame. Decoder Board Installation 4. Physically secure the DH165K0 decoder PCB with the lightboard screws. 5. Attach the four track power pickup wires by shortening and stripping each wire (2 on each end) and soldering these wires to each ...

These are the basic DT400 and DT402 series throttle operating instructions designed to get you “up and running” quickly and to minimize your “frustration level” as you learn to use the throttle.   Turning Track Status On and Off To run your layout you must be sure track power and track status are both ON.  Follow these steps with your DT400 or DT402 series throttle to do this. Press the "PWR" key on the bottom left side of the throttle. The words “+ON  -OFF” will come on in the display. Press the “Y +” key quickly and you should see the ...

Move to decoder installation section? on main site or set up decoder installation notes in TSD?DN123K3 Kato NW2 Installation Instructions 1. Carefully remove the locomotive’s shell from the frame (Figure 1). Notice the orientation of the shell to the frame so that you can reinstall correctly. 2. To remove the Kato NW2 standard lightboard you will need to remove the motor clips first. The NW2 Motor clips can be most easily removed by rotating the motor gently so that the circular motor brush caps release the motor clip. Next pull the motor clip directly off each side of the lightboard. ...

Before sending your Digitrax Command Station or Booster in for repair try these simple steps to see if you can “bring it back from the dead” and save a possible trip to the repair shop.1. Nothing is respondingIf there are NO LEDs lit on the front panel of the Command Station or Booster: Check the power supply to the unit to make sure that it has not been knocked loose in the power socket and that the socket is powered. Check the connections from the power supply to Track A and Track B connections on the front of the unit ...

The Kelana Jaya Rail Line model layout uses WinLok 2.1 running on a PC under Windows 98 to operate the trains, turnouts, signals and to use the feedback from the block detectors for train control. This equipment was configured and programmed to PUTRA's specifications by Dr. Hans R. Tanner of DigiToys Systems. PUTRA specified the following capabilities for the control system used for the simulation: 1. Run eight trains at once in any combination of automated or manual control. 2. Define specific routings and be able to assign automatically or manually any route to any train at the time the ...

DS64 is set up by setting Option Switches (OpSw)This is how to set option switches on the DS64:1. Begin with your DS64 powered up. Turnouts can be either connected or not.2. On the DS64 press and hold the OPS button down for about 3 seconds until the red OPS LED and green ID LED begin to blink alternately. This indicates that the DS64 is ready to change the option switches.3. Using your DCC throttle, select the Switch Address that corresponds to the OpSw number and send the Closed or Thrown command corresponding to the setting you have chosen. Refer to ...

Current production Digitrax decoders use the following numbering system: The first character means that it is a digital decoder. This is always a “D”. The second character indicates the decoder’s physical size. This is based on the smallest "scale" the decoder is designed to fit. This will be a Z, N, H, or G. The third character is the current rating of the decoder. This will be a 1, 2, 3, 4 or 5. We designate 1.25 & 1.5 amp decoders as 1s and 3.5 amp decoders as 3s for simplicity. The fourth character indicates how many functions, including directional ...

How do I set up the SE8C to control semaphores? Installing Semaphore Type Signals with SE8CThe SE8C can be set up to use its 8 turnout motor drive outputs to run 8 three-position semaphore (arm type) signals using slow motion turnout control machines (such as the TortoiseTM machines) as actuators. These 8 semaphore signals are available in addition to the standard 32 LED signal heads on the 8 signal control cables and occupy a separate semaphore address control range.The SE8C automatically sequences the three possible mechanical arm positions to match 3 aspects of red, green and yellow using a position ...

My sound decoder has a capacitor, why do I need a PX112? The capacitor that came with your Digitrax sound decoder is designed to hold up sound operation in the presence of brief power interruptions.  It is not designed to keep the locomotive’s motor and lights running.  Our ears are very sensitive to sound interruptions so, the capacitor on your sound decoder will prevent most of these drop outs on average quality track.  Most people don’t even notice the small pauses in a locomotive’s movement and the small flashes of the lights when the track power is interrupted.  If you ...

  Digitrax Duplex Wireless Functional diagnosis and debug process:   Duplex Background:  The Digitrax Duplex radio system is a two-way RF radio link connecting wireless throttles (DT402D & UT4D) via a UR92 onto LocoNet.  It operates on one of 16 user-selected channels in the 2.4GHz Wi-Fi frequency band.  FCC rules requires that all WI FI devices including the RF24 Duplex transceivers (part of Digitrax Duplex throttles and the UR92) operate co-cooperatively in this 2.4GHz band and have to accept whatever wirelessenvironment is present.  This means that there is no guarantee that Digitrax Duplex will work in all situations or that it will ...

               Decibel measurements on SDH164D Digitrax Sound     Sound level is a logarithmic measure of the effective sound pressure of a sound relative to a reference value. It is measured in decibels (dB) above a standard reference level. The commonly used "zero" reference sound pressure in air is 20 µPa RMS, which is usually considered the threshold of human hearing (at 1 kHz).   Examples of some Loudness rating in both Pa and dB           Hearing damage (over long-term exposure, need not be continuous)                      0.356 Pa                   85 dB Handheld electric mixer                                                                                                                                  65 dB TV (set at home level) at ...

Series 4 decoders like the SDH164k1's will conform to the 10-pin wiring diagram   Function pads for F1 and F2 are located on the SDH164K1 boards on opposite sides by the front headlight. Functions 3 and 4 are located on the 10-pin wire harness, with the Brown wire being the F3 negative and the Yellow wire being the F4 negative.  F3 and F4 functions have a common positive connection to the solder point labeled in the middle of the board.     The common LED sizes used are 3 mm and 5 mm.

Digital Command Control (DCC) has specific electrical requirements that must be provided for your layout control system to operate properly.Input PowerAll DCC systems require an external power supply.  Digitrax manufactures several power supplies for our command stations and boosters: The 3 Amp PS415 (the Zephyr Xtra power supply) The 5 Amp PS515 for all Digitrax 5 amp command stations and boosters The powerful 20 Amp PS2012 can be used for multiple 5 and 8 amp command stations and boosters  Additionally, the PS14 is available to power various other devices for your railroad.  Digitrax strongly encourages you to use our power supplies to insure satisfactory ...